This patch introduces two additional lock modes for tuples: "SELECT FOR
KEY SHARE" and "SELECT FOR NO KEY UPDATE". These don't block each
other, in contrast with already existing "SELECT FOR SHARE" and "SELECT
FOR UPDATE". UPDATE commands that do not modify the values stored in
the columns that are part of the key of the tuple now grab a SELECT FOR
NO KEY UPDATE lock on the tuple, allowing them to proceed concurrently
with tuple locks of the FOR KEY SHARE variety.
Foreign key triggers now use FOR KEY SHARE instead of FOR SHARE; this
means the concurrency improvement applies to them, which is the whole
point of this patch.
The added tuple lock semantics require some rejiggering of the multixact
module, so that the locking level that each transaction is holding can
be stored alongside its Xid. Also, multixacts now need to persist
across server restarts and crashes, because they can now represent not
only tuple locks, but also tuple updates. This means we need more
careful tracking of lifetime of pg_multixact SLRU files; since they now
persist longer, we require more infrastructure to figure out when they
can be removed. pg_upgrade also needs to be careful to copy
pg_multixact files over from the old server to the new, or at least part
of multixact.c state, depending on the versions of the old and new
servers.
Tuple time qualification rules (HeapTupleSatisfies routines) need to be
careful not to consider tuples with the "is multi" infomask bit set as
being only locked; they might need to look up MultiXact values (i.e.
possibly do pg_multixact I/O) to find out the Xid that updated a tuple,
whereas they previously were assured to only use information readily
available from the tuple header. This is considered acceptable, because
the extra I/O would involve cases that would previously cause some
commands to block waiting for concurrent transactions to finish.
Another important change is the fact that locking tuples that have
previously been updated causes the future versions to be marked as
locked, too; this is essential for correctness of foreign key checks.
This causes additional WAL-logging, also (there was previously a single
WAL record for a locked tuple; now there are as many as updated copies
of the tuple there exist.)
With all this in place, contention related to tuples being checked by
foreign key rules should be much reduced.
As a bonus, the old behavior that a subtransaction grabbing a stronger
tuple lock than the parent (sub)transaction held on a given tuple and
later aborting caused the weaker lock to be lost, has been fixed.
Many new spec files were added for isolation tester framework, to ensure
overall behavior is sane. There's probably room for several more tests.
There were several reviewers of this patch; in particular, Noah Misch
and Andres Freund spent considerable time in it. Original idea for the
patch came from Simon Riggs, after a problem report by Joel Jacobson.
Most code is from me, with contributions from Marti Raudsepp, Alexander
Shulgin, Noah Misch and Andres Freund.
This patch was discussed in several pgsql-hackers threads; the most
important start at the following message-ids:
AANLkTimo9XVcEzfiBR-ut3KVNDkjm2Vxh+t8kAmWjPuv@mail.gmail.com1290721684-sup-3951@alvh.no-ip.org1294953201-sup-2099@alvh.no-ip.org1320343602-sup-2290@alvh.no-ip.org1339690386-sup-8927@alvh.no-ip.org4FE5FF020200002500048A3D@gw.wicourts.gov4FEAB90A0200002500048B7D@gw.wicourts.gov
We have seen one too many reports of people trying to use 9.1 extension
files in the old-fashioned way of sourcing them in psql. Not only does
that usually not work (due to failure to substitute for MODULE_PATHNAME
and/or @extschema@), but if it did work they'd get a collection of loose
objects not an extension. To prevent this, insert an \echo ... \quit
line that prints a suitable error message into each extension script file,
and teach commands/extension.c to ignore lines starting with \echo.
That should not only prevent any adverse consequences of loading a script
file the wrong way, but make it crystal clear to users that they need to
do it differently now.
Tom Lane, following an idea of Andrew Dunstan's. Back-patch into 9.1
... there is not going to be much value in this if we wait till 9.2.
It was never terribly consistent to use OR REPLACE (because of the lack of
comparable functionality for data types, operators, etc), and
experimentation shows that it's now positively pernicious in the extension
world. We really want a failure to occur if there are any conflicts, else
it's unclear what the extension-ownership state of the conflicted object
ought to be. Most of the time, CREATE EXTENSION will fail anyway because
of conflicts on other object types, but an extension defining only
functions can succeed, with bad results.
This isn't fully tested as yet, in particular I'm not sure that the
"foo--unpackaged--1.0.sql" scripts are OK. But it's time to get some
buildfarm cycles on it.
sepgsql is not converted to an extension, mainly because it seems to
require a very nonstandard installation process.
Dimitri Fontaine and Tom Lane
corresponding struct definitions. This allows other headers to avoid including
certain highly-loaded headers such as rel.h and relscan.h, instead using just
relcache.h, heapam.h or genam.h, which are more lightweight and thus cause less
unnecessary dependencies.
unnecessary #include lines in it. Also, move some tuple routine prototypes and
macros to htup.h, which allows removal of heapam.h inclusion from some .c
files.
For this to work, a new header file access/sysattr.h needed to be created,
initially containing attribute numbers of system columns, for pg_dump usage.
While at it, make contrib ltree, intarray and hstore header files more
consistent with our header style.
but no database changes have been made since the last CommandCounterIncrement.
This should result in a significant improvement in the number of "commands"
that can typically be performed within a transaction before hitting the 2^32
CommandId size limit. In particular this buys back (and more) the possible
adverse consequences of my previous patch to fix plan caching behavior.
The implementation requires tracking whether the current CommandCounter
value has been "used" to mark any tuples. CommandCounter values stored into
snapshots are presumed not to be used for this purpose. This requires some
small executor changes, since the executor used to conflate the curcid of
the snapshot it was using with the command ID to mark output tuples with.
Separating these concepts allows some small simplifications in executor APIs.
Something for the TODO list: look into having CommandCounterIncrement not do
AcceptInvalidationMessages. It seems fairly bogus to be doing it there,
but exactly where to do it instead isn't clear, and I'm disinclined to mess
with asynchronous behavior during late beta.
remove transactions
use create or replace function
make formatting consistent
set search patch on first line
Add documentation on modifying *.sql to set the search patch, and
mention that major upgrades should still run the installation scripts.
Some of these issues were spotted by Tom today.
installations whose pg_config program does not appear first in the PATH.
Per gripe from Eddie Stanley and subsequent discussions with Fabien Coelho
and others.
