When starting WAL replay from an online checkpoint, the last replayed WAL
record variable was initialized using the checkpoint record's location, even
though the records between the REDO location and the checkpoint record had
not been replayed yet. That was noted as "slightly confusing" but harmless
in the comment, but in some cases, it fooled CheckRecoveryConsistency to
incorrectly conclude that we had already reached a consistent state
immediately at the beginning of WAL replay. That caused the system to accept
read-only connections in hot standby mode too early, and also PANICs with
message "WAL contains references to invalid pages".
Fix by initializing the variables to the REDO location instead.
In 9.2 and above, change CheckRecoveryConsistency() to use
lastReplayedEndRecPtr variable when checking if backup end location has
been reached. It was inconsistently using EndRecPtr for that check, but
lastReplayedEndRecPtr when checking min recovery point. It made no
difference before this patch, because in all the places where
CheckRecoveryConsistency was called the two variables were the same, but
it was always an accident waiting to happen, and would have been wrong
after this patch anyway.
Report and analysis by Tomonari Katsumata, bug #8686. Backpatch to 9.0,
where hot standby was introduced.
I failed to think much about UPDATE/DELETE when implementing LATERAL :-(.
The implemented behavior ended up being that subqueries in the FROM or
USING clause (respectively) could access the update/delete target table as
though it were a lateral reference; which seems fine if they said LATERAL,
but certainly ought to draw an error if they didn't. Fix it so you get a
suitable error when you omit LATERAL. Per report from Emre Hasegeli.
And the same for do_pg_stop_backup. The code in do_pg_* is not allowed
to access the catalogs. For manual base backups, the permissions
check can be handled in the calling function, and for streaming
base backups only users with the required permissions can get past
the authentication step in the first place.
Reported by Antonin Houska, diagnosed by Andres Freund
If a tablespace was crated inside PGDATA it was backed up both as part
of the PGDATA backup and as the backup of the tablespace. Avoid this
by skipping any directory inside PGDATA that contains one of the active
tablespaces.
Dimitri Fontaine and Magnus Hagander
Several previous commits have added columns to various \d queries without
updating their translate_columns[] arrays, leading to potentially incorrect
translations in NLS-enabled builds. Offenders include commit 893686762
(added prosecdef to \df+), c9ac00e6e (added description to \dc+) and
3b17efdfd (added description to \dC+). Fix those cases back to 9.3 or
9.2 as appropriate.
Since this is evidently more easily missed than one would like, in HEAD
also add an Assert that the supplied array is long enough. This requires
an API change for printQuery(), so it seems inappropriate for back
branches, but presumably all future changes will be tested in HEAD anyway.
In HEAD and 9.3, also clean up a whole lot of sloppiness in the emitted
SQL for \dy (event triggers): lack of translatability due to failing to
pass words-to-be-translated through gettext_noop(), inadequate schema
qualification, and sloppy formatting resulting in unnecessarily ugly
-E output.
Peter Eisentraut and Tom Lane, per bug #8702 from Sergey Burladyan
Original users of slru.c were all producing 4-digit filenames, so that
was all that that code was prepared to handle. Changes to multixact.c
in the course of commit 0ac5ad5134 made pg_multixact/members create
5-digit filenames once a certain threshold was reached, which
SlruScanDirectory wasn't prepared to deal with; in particular,
5-digit-name files were not removed during truncation. Change that
routine to make it aware of those files, and have it process them just
like any others.
Right now, some pg_multixact/members directories will contain a mixture
of 4-char and 5-char filenames. A future commit is expected fix things
so that each slru.c user declares the correct maximum width for the
files it produces, to avoid such unsightly mixtures.
Noticed while investigating bug #8673 reported by Serge Negodyuck.
In the 9.2 code for extending multixact/members, the logic was very
simple because the number of entries in a members page was a proper
divisor of 2^32, and thus at 2^32 wraparound the logic for page switch
was identical than at any other page boundary. In commit 0ac5ad5134 I
failed to realize this and introduced code that was not able to go over
the 2^32 boundary. Fix that by ensuring that when we reach the last
page of the last segment we correctly zero the initial page of the
initial segment, using correct uint32-wraparound-safe arithmetic.
Noticed while investigating bug #8673 reported by Serge Negodyuck, as
diagnosed by Andres Freund.
In pg_multixact/members, relying on modulo-2^32 arithmetic for
wraparound handling doesn't work all that well. Because we don't
explicitely track wraparound of the allocation counter for members, it
is possible that the "live" area exceeds 2^31 entries; trying to remove
SLRU segments that are "old" according to the original logic might lead
to removal of segments still in use. To fix, have the truncation
routine use a tailored SlruScanDirectory callback that keeps track of
the live area in actual use; that way, when the live range exceeds 2^31
entries, the oldest segments still live will not get removed untimely.
This new SlruScanDir callback needs to take care not to remove segments
that are "in the future": if new SLRU segments appear while the
truncation is ongoing, make sure we don't remove them. This requires
examination of shared memory state to recheck for false positives, but
testing suggests that this doesn't cause a problem. The original coding
didn't suffer from this pitfall because segments created when truncation
is running are never considered to be removable.
Per Andres Freund's investigation of bug #8673 reported by Serge
Negodyuck.
CREATE EVENT TRIGGER forgot to mark the event trigger as a member of its
extension, and pg_dump didn't pay any attention anyway when deciding
whether to dump the event trigger. Per report from Moshe Jacobson.
Given the obvious lack of testing here, it's rather astonishing that
ALTER EXTENSION ADD/DROP EVENT TRIGGER work, but they seem to.
There was an apparent attempt to limit the target database for
pg_restore to version 7.1.0 or later. Due to a leading zero this
was interpreted as an octal number, which allowed targets with
version numbers down to 2.87.36. The lowest actual release above
that was 6.0.0, so that was effectively the limit.
Since the success of the restore attempt will depend primarily on
on what statements were generated by the dump run, we don't want
pg_restore trying to guess whether a given target should be allowed
based on version number. Allow a connection to any version. Since
it is very unlikely that anyone would be using a recent version of
pg_restore to restore to a pre-6.0 database, this has little to no
practical impact, but it makes the code less confusing to read.
Issue reported and initial patch suggestion from Joel Jacobson
based on an article by Andrey Karpov reporting on issues found by
PVS-Studio static code analyzer. Final patch based on analysis by
Tom Lane. Back-patch to all supported branches.
Instead of looking for characters that aren't valid in JSON numbers, we
simply pass the output string through the JSON number parser, and if it
fails the string is quoted. This means among other things that money and
domains over money will be quoted correctly and generate valid JSON.
Fixes bug #8676 reported by Anderson Cristian da Silva.
Backpatched to 9.2 where JSON generation was introduced.
The bug would only show up if the C sockaddr structure contained
zero in the first byte for a valid address; otherwise it would
fail to fail, which is probably why it went unnoticed for so long.
Patch submitted by Joel Jacobson after seeing an article by Andrey
Karpov in which he reports finding this through static code
analysis using PVS-Studio. While I was at it I moved a definition
of a local variable referenced in the buggy code to a more local
context.
Backpatch to all supported branches.
Most other range operations seem to work all right on domains,
but this one not so much, at least not since commit 918eee0c.
Per bug #8684 from Brett Neumeier.
We can allocate the initial relations-to-drop array when first needed,
instead of at function entry; this avoids allocating it when the
function is not going to do anything, which is most of the time.
Backpatch to 9.3, where this behavior was introduced by commit
279628a0a7.
There's more that could be done here, such as possible reworking of the
code to avoid having to palloc anything, but that doesn't sound as
backpatchable as this relatively minor change.
Per complaint from Noah Misch in
20131031145234.GA621493@tornado.leadboat.com
Updating or locking a row that was already locked by the same
transaction under the same Xid caused a MultiXact to be created; but
this is unnecessary, because there's no usefulness in being able to
differentiate two locks by the same transaction. In particular, if a
transaction executed SELECT FOR UPDATE followed by an UPDATE that didn't
modify columns of the key, we would dutifully represent the resulting
combination as a multixact -- even though a single key-update is
sufficient.
Optimize the case so that only the strongest of both locks/updates is
represented in Xmax. This can save some Xmax's from becoming
MultiXacts, which can be a significant optimization.
This missed optimization opportunity was spotted by Andres Freund while
investigating a bug reported by Oliver Seemann in message
CANCipfpfzoYnOz5jj=UZ70_R=CwDHv36dqWSpwsi27vpm1z5sA@mail.gmail.com
and also directly as a performance regression reported by Dong Ye in
message
d54b8387.000012d8.00000010@YED-DEVD1.vmware.com
Reportedly, this patch fixes the performance regression.
Since the missing optimization was reported as a significant performance
regression from 9.2, backpatch to 9.3.
Andres Freund, tweaked by Álvaro Herrera
If a tuple was locked by transaction A, and transaction B updated it,
the new version of the tuple created by B would be locked by A, yet
visible only to B; due to an oversight in HeapTupleSatisfiesUpdate, the
lock held by A wouldn't get checked if transaction B later deleted (or
key-updated) the new version of the tuple. This might cause referential
integrity checks to give false positives (that is, allow deletes that
should have been rejected).
This is an easy oversight to have made, because prior to improved tuple
locks in commit 0ac5ad5134 it wasn't possible to have tuples created by
our own transaction that were also locked by remote transactions, and so
locks weren't even considered in that code path.
It is recommended that foreign keys be rechecked manually in bulk after
installing this update, in case some referenced rows are missing with
some referencing row remaining.
Per bug reported by Daniel Wood in
CAPweHKe5QQ1747X2c0tA=5zf4YnS2xcvGf13Opd-1Mq24rF1cQ@mail.gmail.com
Tuple freezing was broken in connection to MultiXactIds; commit
8e53ae025d tried to fix it, but didn't go far enough. As noted by
Noah Misch, freezing a tuple whose Xmax is a multi containing an aborted
update might cause locks in the multi to go ignored by later
transactions. This is because the code depended on a multixact above
their cutoff point not having any lock-only member older than the cutoff
point for Xids, which is easily defeated in READ COMMITTED transactions.
The fix for this involves creating a new MultiXactId when necessary.
But this cannot be done during WAL replay, and moreover multixact
examination requires using CLOG access routines which are not supposed
to be used during WAL replay either; so tuple freezing cannot be done
with the old freeze WAL record. Therefore, separate the freezing
computation from its execution, and change the WAL record to carry all
necessary information. At WAL replay time, it's easy to re-execute
freezing because we don't need to re-compute the new infomask/Xmax
values but just take them from the WAL record.
While at it, restructure the coding to ensure all page changes occur in
a single critical section without much room for failures. The previous
coding wasn't using a critical section, without any explanation as to
why this was acceptable.
In replication scenarios using the 9.3 branch, standby servers must be
upgraded before their master, so that they are prepared to deal with the
new WAL record once the master is upgraded; failure to do so will cause
WAL replay to die with a PANIC message. Later upgrade of the standby
will allow the process to continue where it left off, so there's no
disruption of the data in the standby in any case. Standbys know how to
deal with the old WAL record, so it's okay to keep the master running
the old code for a while.
In master, the old freeze WAL record is gone, for cleanliness' sake;
there's no compatibility concern there.
Backpatch to 9.3, where the original bug was introduced and where the
previous fix was backpatched.
Álvaro Herrera and Andres Freund
When locale is "ja_JP.SJIS", nl_langinfo(CODESET) returns "SHIFT_JIS"
on some platforms, at least on RedHat Linux. So the encoding/locale
match table (encoding_match_list) needs the entry. Otherwise client
encoding is set to SQL_ASCII.
Back patch to all supported branches.
Fix an oversight in commit b3aaf9081a: we do
indeed need to process the planner's append_rel_list when copying RTE
subqueries, because if any of them were flattenable UNION ALL subqueries,
the append_rel_list shows which subquery RTEs were pulled up out of which
other ones. Without this, UNION ALL subqueries aren't correctly inserted
into the update plans for inheritance child tables after the first one,
typically resulting in no update happening for those child table(s).
Per report from Victor Yegorov.
Experimentation with this case also exposed a fault in commit
a7b965382c: if an inherited UPDATE/DELETE
was proven totally dummy by constraint exclusion, we might arrive at
add_rtes_to_flat_rtable with root->simple_rel_array being NULL. This
should be interpreted as not having any RelOptInfos. I chose to code
the guard as a check against simple_rel_array_size, so as to also
provide some protection against indexing off the end of the array.
Back-patch to 9.2 where the faulty code was added.
The original performs too poorly; in some scenarios it shows way too
high while profiling. Try to make it a bit smarter to avoid excessive
cosst. In particular, make it have a maximum size, and have entries be
sorted in LRU order; once the max size is reached, evict the oldest
entry to avoid it from growing too large.
Per complaint from Andres Freund in connection with new tuple freezing
code.
This prevents a possible longjmp out of the signal handler if a timeout
or SIGINT occurs while something within the handler has transiently set
ImmediateInterruptOK. For safety we must hold off the timeout or cancel
error until we're back in mainline, or at least till we reach the end of
the signal handler when ImmediateInterruptOK was true at entry. This
syncs these functions with the logic now present in handle_sig_alarm.
AFAICT there is no live bug here in 9.0 and up, because I don't think we
currently can wait for any heavyweight lock inside these functions, and
there is no other code (except read-from-client) that will turn on
ImmediateInterruptOK. However, that was not true pre-9.0: in older
branches ProcessIncomingNotify might block trying to lock pg_listener, and
then a SIGINT could lead to undesirable control flow. It might be all
right anyway given the relatively narrow code ranges in which NOTIFY
interrupts are enabled, but for safety's sake I'm back-patching this.
Serious oversight in commit 16e1b7a1b7:
we should not allow an interrupt to take control away from mainline code
except when ImmediateInterruptOK is set. Just to be safe, let's adopt
the same save-clear-restore dance that's been used for many years in
HandleCatchupInterrupt and HandleNotifyInterrupt, so that nothing bad
happens if a timeout handler invokes code that tests or even manipulates
ImmediateInterruptOK.
Per report of "stuck spinlock" failures from Christophe Pettus, though
many other symptoms are possible. Diagnosis by Andres Freund.
The operation that removes the remaining dead tuples from the page must
be WAL-logged before the setting of the VM bit. Otherwise, if you replay
the WAL to between those two records, you end up with the VM bit set, but
the dead tuples are still there.
Backpatch to 9.3, where this bug was introduced.
Integer overflow showed minus percent and minus remaining time something like this.
239300000 of 3800000000 tuples (-48%) done (elapsed 226.86 s, remaining -696.10 s).
Make the COPY test, which loads most of the large static tables used in
the tests, also explicitly ANALYZE those tables. This allows us to get
rid of various ad-hoc, and rather redundant, ANALYZE commands that had
gotten stuck into various test scripts over time to ensure we got
consistent plan choices. (We could have done a database-wide ANALYZE,
but that would cause stats to get attached to the small static tables
too, which results in plan changes compared to the historical behavior.
I'm not sure that's a good idea, so not going that far for now.)
Back-patch to 9.0, since 9.0 and 9.1 are currently sometimes failing
regression tests for lack of an "ANALYZE tenk1" in the subselect test.
There's no need for this in 8.4 since we didn't print any plans back
then.
The test only needs the one table to be vacuumed. Vacuuming the
database may affect other tests.
Per gripe from Tom Lane. Back-patch to 9.3, where the test was
was added.
An expression such as WHERE (... x IN (SELECT ...) ...) IN (SELECT ...)
could produce an invalid plan that results in a crash at execution time,
if the planner attempts to flatten the outer IN into a semi-join.
This happens because convert_testexpr() was not expecting any nested
SubLinks and would wrongly replace any PARAM_SUBLINK Params belonging
to the inner SubLink. (I think the comment denying that this case could
happen was wrong when written; it's certainly been wrong for quite a long
time, since very early versions of the semijoin flattening logic.)
Per report from Teodor Sigaev. Back-patch to all supported branches.
Previous commit e5de601267 modified dblink
to ensure client encoding matched the server. However the added
PQsetClientEncoding() call added significant overhead. Restore original
performance in the common case where client encoding already matches
server encoding by doing nothing in that case. Applies to all active
branches.
Issue reported and work sponsored by Zonar Systems.
In 247c76a989, I added some code to do fine-grained checking of
MultiXact status of locking/updating transactions when traversing an
update chain. There was a thinko in that patch which would have the
traversing abort, that is return HeapTupleUpdated, when the other
transaction is a committed lock-only. In this case we should ignore it
and return success instead. Of course, in the case where there is a
committed update, HeapTupleUpdated is the correct return value.
A user-visible symptom of this bug is that in REPEATABLE READ and
SERIALIZABLE transaction isolation modes spurious serializability errors
can occur:
ERROR: could not serialize access due to concurrent update
In order for this to happen, there needs to be a tuple that's key-share-
locked and also updated, and the update must abort; a subsequent
transaction trying to acquire a new lock on that tuple would abort with
the above error. The reason is that the initial FOR KEY SHARE is seen
as committed by the new locking transaction, which triggers this bug.
(If the UPDATE commits, then the serialization error is correctly
reported.)
When running a query in READ COMMITTED mode, what happens is that the
locking is aborted by the HeapTupleUpdated return value, then
EvalPlanQual fetches the newest version of the tuple, which is then the
only version that gets locked. (The second time the tuple is checked
there is no misbehavior on the committed lock-only, because it's not
checked by the code that traverses update chains; so no bug.) Only the
newest version of the tuple is locked, not older ones, but this is
harmless.
The isolation test added by this commit illustrates the desired
behavior, including the proper serialization errors that get thrown.
Backpatch to 9.3.
Current OpenSSL code includes a BIO_clear_retry_flags() step in the
sock_write() function. Either we failed to copy the code correctly, or
they added this since we copied it. In any case, lack of the clear step
appears to be the cause of the server lockup after connection loss reported
in bug #8647 from Valentine Gogichashvili. Assume that this is correct
coding for all OpenSSL versions, and hence back-patch to all supported
branches.
Diagnosis and patch by Alexander Kukushkin.
HeapTupleSatisfiesUpdate can very easily "forget" tuple locks while
checking the contents of a multixact and finding it contains an aborted
update, by setting the HEAP_XMAX_INVALID bit. This would lead to
concurrent transactions not noticing any previous locks held by
transactions that might still be running, and thus being able to acquire
subsequent locks they wouldn't be normally able to acquire.
This bug was introduced in commit 1ce150b7bb; backpatch this fix to 9.3,
like that commit.
This change reverts the change to the delete-abort-savept isolation test
in 1ce150b7bb, because that behavior change was caused by this bug.
Noticed by Andres Freund while investigating a different issue reported
by Noah Misch.
Insertion to a non-leaf GIN page didn't make a full-page image of the page,
which is wrong. The code used to do it correctly, but was changed (commit
853d1c3103) because the redo-routine didn't
track incomplete splits correctly when the page was restored from a full
page image. Of course, that was not right way to fix it, the redo routine
should've been fixed instead. The redo-routine was surreptitiously fixed
in 2010 (commit 4016bdef8a), so all we need
to do now is revert the code that creates the record to its original form.
This doesn't change the format of the WAL record.
Backpatch to all supported versions.
pg_dumpall's charter is to be able to recreate a database cluster's
contents in a virgin installation, but it was failing to honor that
contract if the cluster had any ALTER DATABASE SET
default_transaction_read_only settings. By including a SET command
for the connection for each connection opened by pg_dumpall output,
errors are avoided and the source cluster is successfully
recreated.
There was discussion of whether to also set this for the connection
applying pg_dump output, but it was felt that it was both less
appropriate in that context, and far easier to work around.
Backpatch to all supported branches.
Both heap_freeze_tuple() and heap_tuple_needs_freeze() neglected to look
into a multixact to check the members against cutoff_xid. This means
that a very old Xid could survive hidden within a multi, possibly
outliving its CLOG storage. In the distant future, this would cause
clog lookup failures:
ERROR: could not access status of transaction 3883960912
DETAIL: Could not open file "pg_clog/0E78": No such file or directory.
This mostly was problematic when the updating transaction aborted, since
in that case the row wouldn't get pruned away earlier in vacuum and the
multixact could possibly survive for a long time. In many cases, data
that is inaccessible for this reason way can be brought back
heuristically.
As a second bug, heap_freeze_tuple() didn't properly handle multixacts
that need to be frozen according to cutoff_multi, but whose updater xid
is still alive. Instead of preserving the update Xid, it just set Xmax
invalid, which leads to both old and new tuple versions becoming
visible. This is pretty rare in practice, but a real threat
nonetheless. Existing corrupted rows, unfortunately, cannot be repaired
in an automated fashion.
Existing physical replicas might have already incorrectly frozen tuples
because of different behavior than in master, which might only become
apparent in the future once pg_multixact/ is truncated; it is
recommended that all clones be rebuilt after upgrading.
Following code analysis caused by bug report by J Smith in message
CADFUPgc5bmtv-yg9znxV-vcfkb+JPRqs7m2OesQXaM_4Z1JpdQ@mail.gmail.com
and privately by F-Secure.
Backpatch to 9.3, where freezing of MultiXactIds was introduced.
Analysis and patch by Andres Freund, with some tweaks by Álvaro.
It is dangerous to do so, because some code expects to be able to see what's
the true Xmax even if it is aborted (particularly while traversing HOT
chains). So don't do it, and instead rely on the callers to verify for
abortedness, if necessary.
Several race conditions and bugs fixed in the process. One isolation test
changes the expected output due to these.
This also reverts commit c235a6a589, which is no longer necessary.
Backpatch to 9.3, where this function was introduced.
Andres Freund
Commit 9dc842f08 of 8.2 era prevented MultiXact truncation during crash
recovery, because there was no guarantee that enough state had been
setup, and because it wasn't deemed to be a good idea to remove data
during crash recovery anyway. Since then, due to Hot-Standby, streaming
replication and PITR, the amount of time a cluster can spend doing crash
recovery has increased significantly, to the point that a cluster may
even never come out of it. This has made not truncating the content of
pg_multixact/ not defensible anymore.
To fix, take care to setup enough state for multixact truncation before
crash recovery starts (easy since checkpoints contain the required
information), and move the current end-of-recovery actions to a new
TrimMultiXact() function, analogous to TrimCLOG().
At some later point, this should probably done similarly to the way
clog.c is doing it, which is to just WAL log truncations, but we can't
do that for the back branches.
Back-patch to 9.0. 8.4 also has the problem, but since there's no hot
standby there, it's much less pressing. In 9.2 and earlier, this patch
is simpler than in newer branches, because multixact access during
recovery isn't required. Add appropriate checks to make sure that's not
happening.
Andres Freund
While autovacuum dutifully launched anti-multixact-wraparound vacuums
when the multixact "age" was reached, the vacuum code was not aware that
it needed to make them be full table vacuums. As the resulting
partial-table vacuums aren't capable of actually increasing relminmxid,
autovacuum continued to launch anti-wraparound vacuums that didn't have
the intended effect, until age of relfrozenxid caused the vacuum to
finally be a full table one via vacuum_freeze_table_age.
To fix, introduce logic for multixacts similar to that for plain
TransactionIds, using the same GUCs.
Backpatch to 9.3, where permanent MultiXactIds were introduced.
Andres Freund, some cleanup by Álvaro
Parts of the code used autovacuum_freeze_max_age to determine whether
anti-multixact-wraparound vacuums are necessary, while others used a
hardcoded 200000000 value. This leads to problems when
autovacuum_freeze_max_age is set to a non-default value. Use the latter
everywhere.
Backpatch to 9.3, where vacuuming of multixacts was introduced.
Andres Freund
Ensure that the invocation command for postgres or pg_ctl runservice
double-quotes the executable's pathname; failure to do this leads to
trouble when the path contains spaces.
Also, ensure that the path ends in ".exe" in both cases and uses
backslashes rather than slashes as directory separators. The latter issue
is reported to confuse some third-party tools such as Symantec Backup Exec.
Also, rewrite the function to avoid buffer overrun issues by using a
PQExpBuffer instead of a fixed-size static buffer. Combinations of
very long executable pathnames and very long data directory pathnames
could have caused trouble before, for example.
Back-patch to all active branches, since this code has been like this
for a long while.
Naoya Anzai and Tom Lane, reviewed by Rajeev Rastogi
