These algorithms are fundamental and extensively used. The "no-" options
do not work either in 1.1.0 or in other released branches. Therefore the
ability to disable them should be removed.
Reviewed-by: Richard Levitte <levitte@openssl.org>
The handling was Unix centric, already in Configure. Change that to
just collect the value and let the build file templates figure out
what to do with it.
Reviewed-by: Matt Caswell <matt@openssl.org>
Since NDEBUG is defined unconditionally on command line for release
builds, we can omit *_DEBUG options in favour of effective "all-on"
in debug builds exercised though CI.
Reviewed-by: Richard Levitte <levitte@openssl.org>
Reviewed-by: Emilia Käsper <emilia@openssl.org>
- In Configure, register the perl interpreter used to run Configure,
so that's the one being used throughout instead of something else
that Configure happens to find. This is helpful for using a perl
version that's not necessarely first in $PATH:
/opt/perl/5.22.1/bin/perl ./Configure
- Make apps/tsget a generated file, just like apps/CA.pl, so the
perl interpreter registered by Configure becomes the hashbang path
instead of a hardcoded /usr/bin/perl
Reviewed-by: Andy Polyakov <appro@openssl.org>
There are rare cases when an object file will only be used when
building a shared library. To enable this, we introduce
SHARED_SOURCE:
SHARED_SOURCE[libfoo]=dllmain.c
Reviewed-by: Andy Polyakov <appro@openssl.org>
utils/mkrc.pl was added a while ago as a better generator for the
Windows DLL resource file. Finalize the change by removing the
ms/version32.rc generator from Configure and adding resource file
support using mkrc.pl in Configurations/windows-makefile.pl
Reviewed-by: Andy Polyakov <appro@openssl.org>
This is only enabled when the environment variable
CONFIGURE_DEBUG_BUILDINFO is defined. This will cause every line in
every build.info file to be displayed, along with the content of the
skip stack before and after parsing. This can be a very powerful tool
to see that all conditions are working as expected.
Reviewed-by: Rich Salz <rsalz@openssl.org>
We don't currently support cross-compiling of the afalg engine. However
we were failing to explicitly mark it as disabled during Configure leading
to a failed build.
Reviewed-by: Richard Levitte <levitte@openssl.org>
Experience has shown that dynamic engines with their own copy of
libcrypto is problematic, so we disable that possibility.
Reviewed-by: Matt Caswell <matt@openssl.org>
This corrects a fault where the inner IF in this example was still
being acted upon:
IF[0]
...whatever...
IF[1]
...whatever more...
ENDIF
ENDIF
With this change, the inner IF is skipped over.
Reviewed-by: Matt Caswell <matt@openssl.org>
The "extra checks" is a debugging tool to check the config resolving
mechanism. It uses Perl's smart match, which is experimental and
therefore always causes Perl to give out a warning, and it causes
older Perl versions to fail entirely.
So, it gets commented away, but stays otherwise in place, as it may be
useful again.
Reviewed-by: Matt Caswell <matt@openssl.org>
All OpenSSL code has now been transferred to use the new threading API,
so the old one is no longer used and can be removed. We provide some compat
macros for removed functions which are all no-ops.
There is now no longer a need to set locking callbacks!!
Reviewed-by: Richard Levitte <levitte@openssl.org>
According to manuals found here: https://gcc.gnu.org/onlinedocs/, GNU
C version 3 and on support the dependency generation options. We
therefore need to check the gcc version to see if we're going to use
it or makedepend for dependency generation.
Reviewed-by: Andy Polyakov <appro@openssl.org>
Should it be needed because the recipes within a RAW section might
clash with those generated by Configure, it's possible to tell it
not to generate them with the use of OVERRIDES, for example:
SOURCE[libfoo]=foo.c bar.c
OVERRIDES=bar.o
BEGINRAW[Makefile(unix)]
bar.o: bar.c
$(CC) $(CFLAGS) -DSPECIAL -c -o $@ $<
ENDRAW[Makefile(unix)]
Reviewed-by: Rich Salz <rsalz@openssl.org>
In some cases, one might want to generate some source files from
others, that's done as follows:
GENERATE[foo.s]=asm/something.pl $(CFLAGS)
GENERATE[bar.s]=asm/bar.S
The value of each GENERATE line is a command line or part of it.
Configure places no rules on the command line, except the the first
item muct be the generator file. It is, however, entirely up to the
build file template to define exactly how those command lines should
be handled, how the output is captured and so on.
Reviewed-by: Rich Salz <rsalz@openssl.org>
1. Cleaned up eventfd handling
2. Reworked socket setup code to allow other algorithms to be added in
future
3. Fixed compile errors for static build
4. Added error to error stack in all cases of ALG_PERR/ALG_ERR
5. Called afalg_aes_128_cbc() from bind() to avoid race conditions
6. Used MAX_INFLIGHT define in io_getevents system call
7. Coding style fixes
Reviewed-by: Richard Levitte <levitte@openssl.org>
Reviewed-by: Matt Caswell <matt@openssl.org>
