Rename BUF_{strdup,strlcat,strlcpy,memdup,strndup,strnlen}
to OPENSSL_{strdup,strlcat,strlcpy,memdup,strndup,strnlen}
Add #define's for the old names.
Add CRYPTO_{memdup,strndup}, called by OPENSSL_{memdup,strndup} macros.
Reviewed-by: Tim Hudson <tjh@openssl.org>
Loading the config file after processing command line options can
cause problems, e.g. where an engine provides new ciphers/digests
these are not then recoginised on the command line. Move the
default config file loading to before the command line option
processing. Whilst we're doing this we might as well centralise
this instead of doing it individually for each application. Finally
if we do it before the OpenSSL_add_ssl_algorithms() call then
ciphersuites provided by an engine (e.g. GOST) can be available to
the apps.
RT#4085
RT#4086
Reviewed-by: Richard Levitte <levitte@openssl.org>
For those command line options that take the verification options
-CApath and -CAfile, if those options are absent then the default path or
file is used instead. It is not currently possible to specify *no* path or
file at all. This change adds the options -no-CApath and -no-CAfile to
specify that the default locations should not be used to all relevant
applications.
Reviewed-by: Andy Polyakov <appro@openssl.org>
The different apps had the liberty to decide whether they would open their
input and output files in binary mode or not, which could be confusing if
two different apps were handling the same type of file in different ways.
The solution is to centralise the decision of low level file organisation,
and that the apps would use a selection of formats to state the intent of
the file.
Reviewed-by: Tim Hudson <tjh@openssl.org>
Most of all, we needed to sort out which ones are binary and which
ones are text, and make sure they are treated accordingly and
consistently so
Reviewed-by: Tim Hudson <tjh@openssl.org>
Here are the "rules" for handling flags that depend on #ifdef:
- Do not ifdef the enum. Only ifdef the OPTIONS table. All ifdef'd
entries appear at the end; by convention "engine" is last. This
ensures that at run-time, the flag will never be recognized/allowed.
The next two bullets entries are for silencing compiler warnings:
- In the while/switch parsing statement, use #ifdef for the body to
disable it; leave the "case OPT_xxx:" and "break" statements outside
the ifdef/ifndef. See ciphers.c for example.
- If there are multiple options controlled by a single guard, OPT_FOO,
OPT_BAR, etc., put a an #ifdef around the set, and then do "#else"
and a series of case labels and a break. See OPENSSL_NO_AES in cms.c
for example.
Reviewed-by: Matt Caswell <matt@openssl.org>
The module loading feature got broken a while ago, so restore it, but
have it a bit more explicit this time around.
Reviewed-by: Stephen Henson <steve@openssl.org>
For a local variable:
TYPE *p;
Allocations like this are "risky":
p = OPENSSL_malloc(sizeof(TYPE));
if the type of p changes, and the malloc call isn't updated, you
could get memory corruption. Instead do this:
p = OPENSSL_malloc(sizeof(*p));
Also fixed a few memset() calls that I noticed while doing this.
Reviewed-by: Richard Levitte <levitte@openssl.org>
After the finale, the "real" final part. :) Do a recursive grep with
"-B1 -w [a-zA-Z0-9_]*_free" to see if any of the preceeding lines are
an "if NULL" check that can be removed.
Reviewed-by: Tim Hudson <tjh@openssl.org>
No point in proceeding if you're out of memory. So change
*all* OPENSSL_malloc calls in apps to use the new routine which
prints a message and exits.
Reviewed-by: Richard Levitte <levitte@openssl.org>
Many functions had a BIO* parameter, and it was always called
with bio_err. Remove the param and just use bio_err.
Reviewed-by: Matt Caswell <matt@openssl.org>
Make setup_engine be a dummy if NO_ENGINE is enabled.
The option is not enabled if NO_ENGINE is enabled, so the one "wasted"
variable just sits there. Removes some variables and code.
Reviewed-by: Richard Levitte <levitte@openssl.org>
This is merges the old "rsalz-monolith" branch over to master. The biggest
change is that option parsing switch from cascasding 'else if strcmp("-foo")'
to a utility routine and somethin akin to getopt. Also, an error in the
command line no longer prints the full summary; use -help (or --help :)
for that. There have been many other changes and code-cleanup, see
bullet list below.
Special thanks to Matt for the long and detailed code review.
TEMPORARY:
For now, comment out CRYPTO_mem_leaks() at end of main
Tickets closed:
RT3515: Use 3DES in pkcs12 if built with no-rc2
RT1766: s_client -reconnect and -starttls broke
RT2932: Catch write errors
RT2604: port should be 'unsigned short'
RT2983: total_bytes undeclared #ifdef RENEG
RT1523: Add -nocert to fix output in x509 app
RT3508: Remove unused variable introduced by b09eb24
RT3511: doc fix; req default serial is random
RT1325,2973: Add more extensions to c_rehash
RT2119,3407: Updated to dgst.pod
RT2379: Additional typo fix
RT2693: Extra include of string.h
RT2880: HFS is case-insensitive filenames
RT3246: req command prints version number wrong
Other changes; incompatibilities marked with *:
Add SCSV support
Add -misalign to speed command
Make dhparam, dsaparam, ecparam, x509 output C in proper style
Make some internal ocsp.c functions void
Only display cert usages with -help in verify
Use global bio_err, remove "BIO*err" parameter from functions
For filenames, - always means stdin (or stdout as appropriate)
Add aliases for -des/aes "wrap" ciphers.
*Remove support for IISSGC (server gated crypto)
*The undocumented OCSP -header flag is now "-header name=value"
*Documented the OCSP -header flag
Reviewed-by: Matt Caswell <matt@openssl.org>
Start ensuring all OpenSSL "free" routines allow NULL, and remove
any if check before calling them.
This gets ASN1_OBJECT_free and ASN1_STRING_free.
Reviewed-by: Matt Caswell <matt@openssl.org>
Miscellaneous unchecked malloc fixes. Also fixed some mem leaks on error
paths as I spotted them along the way.
Reviewed-by: Tim Hudson <tjh@openssl.org>
X509_V_FLAG_NO_ALT_CHAINS flag. Using this option means that when building
certificate chains, the first chain found will be the one used. Without this
flag, if the first chain found is not trusted then we will keep looking to
see if we can build an alternative chain instead.
Reviewed-by: Dr. Stephen Henson <steve@openssl.org>
Ignore self issued certificates when checking path length constraints.
Duplicate OIDs in policy tree in case they are allocated.
Use anyPolicy from certificate cache and not current tree level.
