Loading the config file after processing command line options can
cause problems, e.g. where an engine provides new ciphers/digests
these are not then recoginised on the command line. Move the
default config file loading to before the command line option
processing. Whilst we're doing this we might as well centralise
this instead of doing it individually for each application. Finally
if we do it before the OpenSSL_add_ssl_algorithms() call then
ciphersuites provided by an engine (e.g. GOST) can be available to
the apps.
RT#4085
RT#4086
Reviewed-by: Richard Levitte <levitte@openssl.org>
The different apps had the liberty to decide whether they would open their
input and output files in binary mode or not, which could be confusing if
two different apps were handling the same type of file in different ways.
The solution is to centralise the decision of low level file organisation,
and that the apps would use a selection of formats to state the intent of
the file.
Reviewed-by: Tim Hudson <tjh@openssl.org>
Most of all, we needed to sort out which ones are binary and which
ones are text, and make sure they are treated accordingly and
consistently so
Reviewed-by: Tim Hudson <tjh@openssl.org>
There's no reason why we should default to a output format that is
old, and confusing in some cases.
This affects the commands "ca", "crl", "req" and "x509".
Reviewed-by: Rich Salz <rsalz@openssl.org>
When generating a private key, try to make the output file be readable
only by the owner. Put it in CHANGES file since it might be noticeable.
Add "int private" flag to apps that write private keys, and check that it's
set whenever we do write a private key. Checked via assert so that this
bug (security-related) gets fixed. Thanks to Viktor for help in tracing
the code-paths where private keys are written.
Reviewed-by: Viktor Dukhovni <viktor@openssl.org>
Here are the "rules" for handling flags that depend on #ifdef:
- Do not ifdef the enum. Only ifdef the OPTIONS table. All ifdef'd
entries appear at the end; by convention "engine" is last. This
ensures that at run-time, the flag will never be recognized/allowed.
The next two bullets entries are for silencing compiler warnings:
- In the while/switch parsing statement, use #ifdef for the body to
disable it; leave the "case OPT_xxx:" and "break" statements outside
the ifdef/ifndef. See ciphers.c for example.
- If there are multiple options controlled by a single guard, OPT_FOO,
OPT_BAR, etc., put a an #ifdef around the set, and then do "#else"
and a series of case labels and a break. See OPENSSL_NO_AES in cms.c
for example.
Reviewed-by: Matt Caswell <matt@openssl.org>
The module loading feature got broken a while ago, so restore it, but
have it a bit more explicit this time around.
Reviewed-by: Stephen Henson <steve@openssl.org>
Create app_load_config(), a routine to load config file. Remove the
"always load config" from the main app. Change the places that used to
load config to call the new common routine.
Reviewed-by: Richard Levitte <levitte@openssl.org>
The file name given to -CAserial might not exist yet. The
-CAcreateserial option decides if this is ok or not.
Previous to this change, -CAserial was a type '<' option, and in that
case, the existence of the file given as argument is tested quite
early, and is a failure if it doesn't. With the type 's' option, the
argument is just a string that the application can do whatever it
wants with.
Reviewed-by: Rich Salz <rsalz@openssl.org>
After the finale, the "real" final part. :) Do a recursive grep with
"-B1 -w [a-zA-Z0-9_]*_free" to see if any of the preceeding lines are
an "if NULL" check that can be removed.
Reviewed-by: Tim Hudson <tjh@openssl.org>
No point in proceeding if you're out of memory. So change
*all* OPENSSL_malloc calls in apps to use the new routine which
prints a message and exits.
Reviewed-by: Richard Levitte <levitte@openssl.org>
Make setup_engine be a dummy if NO_ENGINE is enabled.
The option is not enabled if NO_ENGINE is enabled, so the one "wasted"
variable just sits there. Removes some variables and code.
Reviewed-by: Richard Levitte <levitte@openssl.org>
This is merges the old "rsalz-monolith" branch over to master. The biggest
change is that option parsing switch from cascasding 'else if strcmp("-foo")'
to a utility routine and somethin akin to getopt. Also, an error in the
command line no longer prints the full summary; use -help (or --help :)
for that. There have been many other changes and code-cleanup, see
bullet list below.
Special thanks to Matt for the long and detailed code review.
TEMPORARY:
For now, comment out CRYPTO_mem_leaks() at end of main
Tickets closed:
RT3515: Use 3DES in pkcs12 if built with no-rc2
RT1766: s_client -reconnect and -starttls broke
RT2932: Catch write errors
RT2604: port should be 'unsigned short'
RT2983: total_bytes undeclared #ifdef RENEG
RT1523: Add -nocert to fix output in x509 app
RT3508: Remove unused variable introduced by b09eb24
RT3511: doc fix; req default serial is random
RT1325,2973: Add more extensions to c_rehash
RT2119,3407: Updated to dgst.pod
RT2379: Additional typo fix
RT2693: Extra include of string.h
RT2880: HFS is case-insensitive filenames
RT3246: req command prints version number wrong
Other changes; incompatibilities marked with *:
Add SCSV support
Add -misalign to speed command
Make dhparam, dsaparam, ecparam, x509 output C in proper style
Make some internal ocsp.c functions void
Only display cert usages with -help in verify
Use global bio_err, remove "BIO*err" parameter from functions
For filenames, - always means stdin (or stdout as appropriate)
Add aliases for -des/aes "wrap" ciphers.
*Remove support for IISSGC (server gated crypto)
*The undocumented OCSP -header flag is now "-header name=value"
*Documented the OCSP -header flag
Reviewed-by: Matt Caswell <matt@openssl.org>
Miscellaneous unchecked malloc fixes. Also fixed some mem leaks on error
paths as I spotted them along the way.
Reviewed-by: Tim Hudson <tjh@openssl.org>
Reduces number of silly casts in OpenSSL code and likely most
applications. Consistent with (char *) for "peername" value from
X509_check_host() and X509_VERIFY_PARAM_get0_peername().
