openldap/doc/guide/admin/tuning.sdf

# $OpenLDAP$
# Copyright 1999-2009 The OpenLDAP Foundation, All Rights Reserved.
# COPYING RESTRICTIONS APPLY, see COPYRIGHT.

H1: Tuning

This is perhaps one of the most important chapters in the guide, because if 
you have not tuned {{slapd}}(8) correctly or grasped how to design your
directory and environment, you can expect very poor performance.

Reading, understanding and experimenting using the instructions and information
in the following sections, will enable you to fully understand how to tailor 
your directory server to your specific requirements.

It should be noted that the following information has been collected over time
from our community based FAQ. So obviously the benefit of this real world experience
and advice should be of great value to the reader.


H2: Performance Factors

Various factors can play a part in how your directory performs on your chosen 
hardware and environment. We will attempt to discuss these here.


H3: Memory

Scale your cache to use available memory and increase system memory if you can.

See {{SECT:Caching}}


H3: Disks

Use fast subsystems. Put each database and logs on separate disks configurable
via {{DB_CONFIG}}:

>       # Data Directory
>       set_data_dir /data/db
>       
>       # Transaction Log settings
>       set_lg_dir /logs


H3: Network Topology

http://www.openldap.org/faq/data/cache/363.html

Drawing here.


H3: Directory Layout Design

Reference to other sections and good/bad drawing here.


H3: Expected Usage

Discussion.


H2: Indexes

H3: Understanding how a search works

If you're searching on a filter that has been indexed, then the search reads 
the index and pulls exactly the entries that are referenced by the index. 
If the filter term has not been indexed, then the search must read every single
 entry in the target scope and test to see if each entry matches the filter. 
Obviously indexing can save a lot of work when it's used correctly.

H3: What to index

You should create indices to match the actual filter terms used in
search queries. 

>        index cn,sn,givenname,mail eq

Each attribute index can be tuned further by selecting the set of index types to generate. For example, substring and approximate search for organizations (o) may make little sense (and isn't like done very often). And searching for {{userPassword}} likely makes no sense what so ever.

General rule: don't go overboard with indexes. Unused indexes must be maintained and hence can only slow things down. 

See {{slapd.conf}}(8) and {{slapdindex}}(8) for more information


H3: Presence indexing

If your client application uses presence filters and if the
target attribute exists on the majority of entries in your target scope, then
all of those entries are going to be read anyway, because they are valid
members of the result set. In a subtree where 100% of the
entries are going to contain the same attributes, the presence index does
absolutely NOTHING to benefit the search, because 100% of the entries match
that presence filter. 

So the resource cost of generating the index is a
complete waste of CPU time, disk, and memory. Don't do it unless you know
that it will be used, and that the attribute in question occurs very
infrequently in the target data. 

Almost no applications use presence filters in their search queries. Presence
indexing is pointless when the target attribute exists on the majority of
entries in the database. In most LDAP deployments, presence indexing should
not be done, it's just wasted overhead.

See the {{Logging}} section below on what to watch our for if you have a frequently searched
for attribute that is unindexed.


H2: Logging

H3: What log level to use

The default of {{loglevel stats}} (256) is really the best bet. There's a corollary to 
this when problems *do* arise, don't try to trace them using syslog. 
Use the debug flag instead, and capture slapd's stderr output. syslog is too 
slow for debug tracing, and it's inherently lossy - it will throw away messages when it
can't keep up.

Contrary to popular belief, {{loglevel 0}} is not ideal for production as you 
won't be able to track when problems first arise.

H3: What to watch out for

The most common message you'll see that you should pay attention to is:

>       "<= bdb_equality_candidates: (foo) index_param failed (18)"

That means that some application tried to use an equality filter ({{foo=<somevalue>}}) 
and attribute {{foo}} does not have an equality index. If you see a lot of these
messages, you should add the index. If you see one every month or so, it may
be acceptable to ignore it.

The default syslog level is stats (256) which logs the basic parameters of each
request; it usually produces 1-3 lines of output. On Solaris and systems that
only provide synchronous syslog, you may want to turn it off completely, but
usually you want to leave it enabled so that you'll be able to see index
messages whenever they arise. On Linux you can configure syslogd to run
asynchronously, in which case the performance hit for moderate syslog traffic
pretty much disappears.

H3: Improving throughput

You can improve logging performance on some systems by configuring syslog not 
to sync the file system with every write ({{man syslogd/syslog.conf}}). In Linux, 
you can prepend the log file name with a "-" in {{syslog.conf}}. For example, 
if you are using the default LOCAL4 logging you could try:

>       # LDAP logs
>       LOCAL4.*         -/var/log/ldap

For syslog-ng, add or modify the following line in {{syslog-ng.conf}}:

>       options { sync(n); };

where n is the number of lines which will be buffered before a write.


H2: Caching

We all know what caching is, don't we? 

In brief, "A cache is a block of memory for temporary storage of data likely 
to be used again" - {{URL:http://en.wikipedia.org/wiki/Cache}}

There are 3 types of caches, BerkeleyDB's own cache, {{slapd}}(8) 
entry cache and {{TERM:IDL}} (IDL) cache.


H3: Berkeley DB Cache

There are two ways to tune for the BDB cachesize:

(a) BDB cache size necessary to load the database via slapadd in optimal time

(b) BDB cache size necessary to have a high performing running slapd once the data is loaded

For (a), the optimal cachesize is the size of the entire database.  If you 
already have the database loaded, this is simply a 

>       du -c -h *.bdb 

in the directory containing the OpenLDAP ({{/usr/local/var/openldap-data}}) data.

For (b), the optimal cachesize is just the size of the {{id2entry.bdb}} file, 
plus about 10% for growth.

The tuning of {{DB_CONFIG}} should be done for each BDB type database 
instantiated (back-bdb, back-hdb).

Note that while the {{TERM:BDB}} cache is just raw chunks of memory and 
configured as a memory size, the {{slapd}}(8) entry cache holds parsed entries, 
and the size of each entry is variable. 

There is also an IDL cache which is used for Index Data Lookups. 
If you can fit all of your database into slapd's entry cache, and all of your 
index lookups fit in the IDL cache, that will provide the maximum throughput. 

If not, but you can fit the entire database into the BDB cache, then you 
should do that and shrink the slapd entry cache as appropriate. 

Failing that, you should balance the BDB cache against the entry cache.

It is worth noting that it is not absolutely necessary to configure a BerkeleyDB 
cache equal in size to your entire database. All that you need is a cache 
that's large enough for your "working set." 

That means, large enough to hold all of the most frequently accessed data, 
plus a few less-frequently accessed items.

For more information, please see: {{URL:http://www.oracle.com/technology/documentation/berkeley-db/db/ref/am_conf/cachesize.html}}

H4: Calculating Cachesize

The back-bdb database lives in two main files, {{F:dn2id.bdb}} and {{F:id2entry.bdb}}. 
These are B-tree databases. We have never documented the back-bdb internal 
layout before, because it didn't seem like something anyone should have to worry 
about, nor was it necessarily cast in stone. But here's how it works today, 
in OpenLDAP 2.4.

A B-tree is a balanced tree; it stores data in its leaf nodes and bookkeeping 
data in its interior nodes (If you don't know what tree data structures look
 like in general, Google for some references, because that's getting far too 
elementary for the purposes of this discussion).

For decent performance, you need enough cache memory to contain all the nodes 
along the path from the root of the tree down to the particular data item 
you're accessing. That's enough cache for a single search. For the general case, 
you want enough cache to contain all the internal nodes in the database. 

>       db_stat -d

will tell you how many internal pages are present in a database. You should 
check this number for both dn2id and id2entry.

Also note that {{id2entry}} always uses 16KB per "page", while {{dn2id}} uses whatever 
the underlying filesystem uses, typically 4 or 8KB. To avoid thrashing the, 
your cache must be at least as large as the number of internal pages in both 
the {{dn2id}} and {{id2entry}} databases, plus some extra space to accommodate the actual 
leaf data pages.

For example, in my OpenLDAP 2.4 test database, I have an input LDIF file that's 
about 360MB. With the back-hdb backend this creates a {{dn2id.bdb}} that's 68MB, 
and an {{id2entry}} that's 800MB. db_stat tells me that {{dn2id}} uses 4KB pages, has 
433 internal pages, and 6378 leaf pages. The id2entry uses 16KB pages, has 52 
internal pages, and 45912 leaf pages. In order to efficiently retrieve any 
single entry in this database, the cache should be at least

>       (433+1) * 4KB + (52+1) * 16KB in size: 1736KB + 848KB =~ 2.5MB.

This doesn't take into account other library overhead, so this is even lower 
than the barest minimum. The default cache size, when nothing is configured, 
is only 256KB. 

This 2.5MB number also doesn't take indexing into account. Each indexed attribute 
uses another database file of its own, using a Hash structure. 

Unlike the B-trees, where you only need to touch one data page to find an entry 
of interest, doing an index lookup generally touches multiple keys, and the 
point of a hash structure is that the keys are evenly distributed across the 
data space. That means there's no convenient compact subset of the database that 
you can keep in the cache to insure quick operation, you can pretty much expect 
references to be scattered across the whole thing. My strategy here would be to 
provide enough cache for at least 50% of all of the hash data. 

>   (Number of hash buckets + number of overflow pages + number of duplicate pages) * page size / 2.

The objectClass index for my example database is 5.9MB and uses 3 hash buckets 
and 656 duplicate pages. So:

>   ( 3 + 656 ) * 4KB / 2 =~ 1.3MB.

With only this index enabled, I'd figure at least a 4MB cache for this backend. 
(Of course you're using a single cache shared among all of the database files, 
so the cache pages will most likely get used for something other than what you 
accounted for, but this gives you a fighting chance.)

With this 4MB cache I can slapcat this entire database on my 1.3GHz PIII in 
1 minute, 40 seconds. With the cache doubled to 8MB, it still takes the same 1:40s. 
Once you've got enough cache to fit the B-tree internal pages, increasing it 
further won't have any effect until the cache really is large enough to hold 
100% of the data pages. I don't have enough free RAM to hold all the 800MB 
id2entry data, so 4MB is good enough.

With back-bdb and back-hdb you can use "db_stat -m" to check how well the 
database cache is performing. 

For more information on {{db_stat}}: {{URL:http://www.oracle.com/technology/documentation/berkeley-db/db/utility/db_stat.html}}

H3: {{slapd}}(8) Entry Cache (cachesize)

The {{slapd}}(8) entry cache operates on decoded entries. The rationale - entries 
in the entry cache can be used directly, giving the fastest response. If an entry 
isn't in the entry cache but can be extracted from the BDB page cache, that will 
avoid an I/O but it will still require parsing, so this will be slower. 

If the entry is in neither cache then BDB will have to flush some of its current 
cached pages and bring in the needed pages, resulting in a couple of expensive 
I/Os as well as parsing.

The most optimal value is of course, the entire number of entries in the database.  
However, most directory servers don't consistently serve out their entire database, so setting this to a lesser number that more closely matches the believed working set of data is 
sufficient. This is the second most important parameter for the DB.

As far as balancing the entry cache vs the BDB cache - parsed entries in memory 
are generally about twice as large as they are on disk. 

As we have already mentioned, not having a proper database cache size will 
cause performance issues. These issues are not an indication of corruption 
occurring in the database. It is merely the fact that the cache is thrashing 
itself that causes performance/response time to slowdown. 


H3: {{TERM:IDL}} Cache (idlcachesize)

Each IDL holds the search results from a given query, so the IDL cache will 
end up holding the most frequently requested search results.  For back-bdb, 
it is generally recommended to match the "cachesize" setting.  For back-hdb, 
it is generally recommended to be 3x"cachesize".

{NOTE: The idlcachesize setting directly affects search performance}


H3: {{slapd}}(8) Threads

{{slapd}}(8) can process requests via a configurable number of thread, which 
in turn affects the in/out rate of connections.

This value should generally be a function of the number of "real" cores on 
the system, for example on a server with 2 CPUs with one core each, set this 
to 8, or 4 threads per real core.  This is a "read" maximized value. The more 
threads that are configured per core, the slower {{slapd}}(8) responds for 
"read" operations.  On the flip side, it appears to handle write operations 
faster in a heavy write/low read scenario.

The upper bound for good read performance appears to be 16 threads (which
also happens to be the default setting).