This is a follow up to PR https://github.com/Unidata/netcdf-c/pull/1173
Sorry that it is so big, but leak suppression can be complex.
This PR fixes all remaining memory leaks -- as determined by
-fsanitize=address, and with the exceptions noted below.
Unfortunately. there remains a significant leak that I cannot
solve. It involves vlens, and it is unclear if the leak is
occurring in the netcdf-c library or the HDF5 library.
I have added a check_PROGRAM to the ncdump directory to show the
problem. The program is called tst_vlen_demo.c To exercise it,
build the netcdf library with -fsanitize=address enabled. Then
go into ncdump and do a "make clean check". This should build
tst_vlen_demo without actually executing it. Then do the
command "./tst_vlen_demo" to see the output of the memory
checker. Note the the lost malloc is deep in the HDF5 library
(in H5Tvlen.c).
I am temporarily working around this error in the following way.
1. I modified several test scripts to not execute known vlen tests
that fail as described above.
2. Added an environment variable called NC_VLEN_NOTEST.
If set, then those specific tests are suppressed.
This should mean that the --disable-utilities option to
./configure should not need to be set to get a memory leak clean
build. This should allow for detection of any new leaks.
Note: I used an environment variable rather than a ./configure
option to control the vlen tests. This is because it is
temporary (I hope) and because it is a bit tricky for shell
scripts to access ./configure options.
Finally, as before, this only been tested with netcdf-4 and hdf5 support.
stored in the _NCProperties attribute to allow two things:
1. capture of additional library dependencies (over and above
hdf5)
2. Recognition of non-netcdf libraries that create netcdf-4 format
files.
To this end, the _NCProperties format has been extended to be
and arbitrary set of key=value pairs separated by commas.
This new format has version = 2, and uses commas as the pair separator.
Thus the general form is:
_NCProperties = "version=2,key1=value,key2=value2..." ;
This new version is accompanied by a new ./configure option of the form
--with-ncproperties="key1=value1,key2=value2..."
that specifies pairs to add to the _NCProperties attribute for all
files created with that netcdf library.
At this point, what is missing is some programmatic way to
specify either all the pairs or additional pairs
to the _NCProperties attribute. Not sure of the best way
to do this.
Builders using non-netcdf libraries can specify
whatever they want in the key value pairs (as long
as the version=2 is specified first).
By convention, the primary library is expected to be the
the first pair after the leading version=2 pair, but this
is convention only and is neither required nor enforced.
Related changes:
1. Fixed the tests that check _NCProperties to properly operate with version=2.
2. When reading a version 1 _NCProperties attribute, convert it to look
like a version 2 attribute.
2. Added some version 2 tests to ncdump/tst_fileinfo.c and
ncdump/tst_fileinfo.sh
Misc Changes:
1. Fix minor problem in ncdap_test/testurl.sh where a parameter to
buildurl needed to be quoted.
2. Minor fix to ncgen to swap switches -H and -h to be consistent
with other utilities.
3. Document the -M flag in nccopy usage() and the nccopy man page.
4. Modify a test case to use the nccopy -M flag.
After a long discussion, I implemented the rules at the end of that issue.
They are documented in nccopy.1.
Additionally, I added a new, per-variable, -c flag that allows
for the direct setting of the chunking parameters for a variable.
The form is
-c var:c1,c2,...ck
where var is the name of the variable (possibly a fully qualified name)
and the ci are the chunksizes for that variable. It must be the case
that the rank of the variable is k. If the new form is used as well
as the old form, then the new form overrides the old form for the
specified variable. Note that multiple occurrences of the new form
-c flag may be specified.
Misc. Other fixes
1. Added -M <size> option to nccopy to specify the minimum
allowable chunksize.
2. Removed the unused variables from bigmeta.c
(Issue https://github.com/Unidata/netcdf-c/issues/1079)
3. Fixed failure of nc_test4/tst_filter.sh by using the new -M
flag (#1) to allow filter test on a small chunk size.
Fix https://github.com/Unidata/netcdf-c/issues/962
1. remove the --disable-diskless option since it is no
longer needed. Similarly for CMakeLists.txt.
2. Fixed nc4files.c where BAIL and return were mixed
leading to situation where cleanup code was not
being invoked. This probably occurs elsewhere,
but I did not find any specifically.
re pull request https://github.com/Unidata/netcdf-c/pull/405
re pull request https://github.com/Unidata/netcdf-c/pull/446
Notes:
1. This branch is a cleanup of the magic.dmh branch.
2. magic.dmh was originally merged, but caused problems with parallel IO.
It was re-issued as pull request https://github.com/Unidata/netcdf-c/pull/446.
3. This branch + pull request replace any previous pull requests and magic.dmh branch.
Given an otherwise valid netCDF file that has a corrupted header,
the netcdf library currently crashes. Instead, it should return
NC_ENOTNC.
Additionally, the NC_check_file_type code does not do the
forward search required by hdf5 files. It currently only looks
at file position 0 instead of 512, 1024, 2048,... Also, it turns
out that the HDF4 magic number is assumed to always be at the
beginning of the file (unlike HDF5).
The change is localized to libdispatch/dfile.c See
https://support.hdfgroup.org/release4/doc/DSpec_html/DS.pdf
Also, it turns out that the code in NC_check_file_type is duplicated
(mostly) in the function libsrc4/nc4file.c#nc_check_for_hdf.
This branch does the following.
1. Make NC_check_file_type return NC_ENOTNC instead of crashing.
2. Remove nc_check_for_hdf and centralize all file format checking
NC_check_file_type.
3. Add proper forward search for HDF5 files (but not HDF4 files)
to look for the magic number at offsets of 0, 512, 1024...
4. Add test tst_hdf5_offset.sh. This tests that hdf5 files with
an offset are properly recognized. It does so by prefixing
a legal file with some number of zero bytes: 512, 1024, etc.
5. Off-topic: Added -N flag to ncdump to force a specific output dataset name.
