https://github.com/Unidata/netcdf-c/issues/1168https://github.com/Unidata/netcdf-c/issues/1163https://github.com/Unidata/netcdf-c/issues/1162
This PR partially fixes memory leaks in the netcdf-c library,
in the ncdump utility, and in some test cases.
The netcdf-c library now runs memory clean with the assumption
that the --disable-utilities option is used. The primary remaining
problem is ncgen. Once that is fixed, I believe the netcdf-c library
will run memory clean with no limitations.
Notes
-----------
1. Memory checking was performed using gcc -fsanitize=address.
Valgrind-based testing has yet to be performed.
2. The pnetcdf, hdf4, and examples code has not been tested.
Misc. Non-leak changes
1. Make tst_diskless2 only run when netcdf4 is enabled (issue 1162)
2. Fix CmakeLists.txt to turn off logging if ENABLE_NETCDF_4 is OFF
3. Isolated all my debug scripts into a single top-level directory
called debug
4. Fix some USE_NETCDF4 dependencies in nc_test and nc_test4 Makefile.am
re: https://github.com/Unidata/netcdf-c/issues/1154
Inadvertently, the behavior of NC_DISKLESS with nc_create() was
changed in release 4.6.1. Previously, the NC_WRITE flag needed
to be explicitly used with NC_DISKLESS in order to cause the
created file to be persisted to disk.
Additional analyis indicated that the current NC_DISKLESS
implementation was seriously flawed.
This PR attempts to clean up and regularize the situation with
respect to NC_DISKLESS control. One important aspect of diskless
operation is that there are two different notions of write.
1. The file is read-write vs read-only when using the netcdf API.
2. The file is persisted or not to disk at nc_close().
Previously, these two were conflated. The rules now are
as follows.
1. NC_DISKLESS + NC_WRITE means that the file is read/write using the netcdf API
2. NC_DISKLESS + NC_PERSIST means that the file is persisted to a disk file at nc_close.
3. NC_DISKLESS + NC_PERSIST + NC_WRITE means both 1 and 2.
The NC_PERSIST flag is new and takes over the obsolete NC_MPIPOSIX flag.
NC_MPIPOSIX is still defined, but is now an alias for the NC_MPIIO flag.
It is also now the case that for netcdf-4, NC_DISKLESS is independent
of NC_INMEMORY and in fact it is an error to specify both flags
simultaneously.
Finally, the MMAP code was fixed to use NC_PERSIST as well.
Also marked MMAP as deprecated.
Also added a test case to test various combinations of NC_DISKLESS,
NC_PERSIST, and NC_WRITE.
This PR affects a number of files and especially test cases
that used NC_DISKLESS.
Misc. Unrelated fixes
1. fixed some warnings in ncdump/dumplib.c
stored in the _NCProperties attribute to allow two things:
1. capture of additional library dependencies (over and above
hdf5)
2. Recognition of non-netcdf libraries that create netcdf-4 format
files.
To this end, the _NCProperties format has been extended to be
and arbitrary set of key=value pairs separated by commas.
This new format has version = 2, and uses commas as the pair separator.
Thus the general form is:
_NCProperties = "version=2,key1=value,key2=value2..." ;
This new version is accompanied by a new ./configure option of the form
--with-ncproperties="key1=value1,key2=value2..."
that specifies pairs to add to the _NCProperties attribute for all
files created with that netcdf library.
At this point, what is missing is some programmatic way to
specify either all the pairs or additional pairs
to the _NCProperties attribute. Not sure of the best way
to do this.
Builders using non-netcdf libraries can specify
whatever they want in the key value pairs (as long
as the version=2 is specified first).
By convention, the primary library is expected to be the
the first pair after the leading version=2 pair, but this
is convention only and is neither required nor enforced.
Related changes:
1. Fixed the tests that check _NCProperties to properly operate with version=2.
2. When reading a version 1 _NCProperties attribute, convert it to look
like a version 2 attribute.
2. Added some version 2 tests to ncdump/tst_fileinfo.c and
ncdump/tst_fileinfo.sh
Misc Changes:
1. Fix minor problem in ncdap_test/testurl.sh where a parameter to
buildurl needed to be quoted.
2. Minor fix to ncgen to swap switches -H and -h to be consistent
with other utilities.
3. Document the -M flag in nccopy usage() and the nccopy man page.
4. Modify a test case to use the nccopy -M flag.
