- fix HTTP/2 check to not declare a connection dead when
the read attempt results in EAGAIN
- add H2-PROXY alive check as for HTTP/2 that was missing
and is needed
- add attach/detach around Curl_conn_is_alive() and remove
these in filter methods
- add checks for number of connections used in some test_10
proxy tunneling tests
Closes#11368
- refs #11357, where it was reported that HTTP/1.1 downgrades
no longer works
- fixed with suggested change
- added test_05_03 and a new handler in the curltest module
to reproduce that downgrades work
Fixes#11357Closes#11362
Reported-by: Jay Satiro
quote.d was missing a .IP at the end which caused the paragraphs
generated for See-also, Multi, and Example to not be indented correctly.
I also remove a redundant "This option can be used multiple times.", and
replaced .IP "item" with .TP .B "item" to make more clear which lines
are part of the list of commands and which aren't.
Closes#11371
At least msys2 perl v5.32.1 doesn't seem to define this signal. Since
this signal is only used for debugging, just ignore if setting it fails.
Reported-by: Marcel Raad
Fixes#11350Closes#11366
After a test failure log a consistent log message to make it easier to
parse the log file. Also, log a consistent message with "ignored" for
failures that cause the test to be not considered at all. These should
perhaps be counted in the skipped category, but this commit does not
change that behaviour.
The memory check character was erroneously omitted if the memory
checking file was not available for some reason, making the block of
characters an inconsistent length.
- refs #11203 where hyper was reported as being slow
- fixes hyper_executor_poll to loop until it is out of
tasks as advised by @seanmonstar in https://github.com/hyperium/hyper/issues/3237
- added a fix in hyper io handling for detecting EAGAIN
- added some debug logs to see IO results
- pytest http/1.1 test cases pass
- pytest h2 test cases fail on connection reuse. HTTP/2
connection reuse does not seem to work. Hyper submits
a request on a reused connection, curl's IO works and
thereafter hyper declares `Hyper: [1] operation was canceled: connection closed`
on stderr without any error being logged before.
Fixes#11203
Reported-by: Gisle Vanem
Advised-by: Sean McArthur
Closes#11344
- fixes#11242 where 100% CPU on uploads was reported
- fixes possible stalls on last part of a request body when
that information could not be fully send on the connection
due to an EAGAIN
- applies the same EGAIN handling to HTTP/2 proxying
Reported-by: Sergey Alirzaev
Fixed#11242Closes#11342
This shows how to setup OpenSSL mutex callbacks, but this is not
necessary since OpenSSL 1.1.0 - meaning that no currently supported
OpenSSL version requires this anymore
Closes#11341
Errors reading and writing to the pipes are now better detected and
propagated up to the main test loop so it can be cleanly shut down. Such
errors are usually due to a runner dying so it doesn't make much sense
to try to continue the test run.
If the controller dies unexpectedly, have the runner stop its servers
and exit cleanly. Otherwise, the orphaned servers will stay running in
the background.
Give more information about test harness error conditions to help figure
out what might be wrong. Print some internal test state when SIGUSR1 is
sent to runtests.pl.
Ref: #11328
Since the SIGINT handler now just sets a flag that must be checked in the
main controller loop, make sure that runs periodically. Rather than
blocking on a response from a test runner near the end of the test run,
add a short timeout to allow it.
Stop checking the timeout used by the client under test (for most
tests). The timeout will change if the TFTP test server is slow (such as
happens on an overprovisioned CI server) because the client will retry
and reduce its timeout, and the actual value is not important for most
tests.
test285 is changed a different way, by increasing the connect timeout.
This improves test coverage by allowing the changed timeout value to be
checked, but improves reliability with a carefully-chosen timeout that
not only allows twice the time to respond as before, but also allows
several retries before the client will change its timeout value.
Ref: #11328
Since the socket is not connected then the call fails. When the call
fails, failf() is called to write an error message that is then
surviving and is returned when the *real* error occurs later. The
earlier, incorrect, error therefore hides the actual error message.
This could be seen in stderr for test 1007
Test 1007 has now been extended to verify the stderr message.
Closes#11332
Previously it would count the size of the entire outgoing request and
not just the size of only the Cookie: header field - which was the
intention.
This could make the check be off by several hundred bytes in some cases.
Closes#11331
- Use CURL_FORMAT_CURL_OFF_T where %zd was erroneously used for some
curl_off_t variables.
- Use %zu where %zd was erroneously used for some size_t variables.
Prior to this change some of the Windows CI tests were failing because
in Windows 32-bit targets have a 32-bit size_t and a 64-bit curl_off_t.
When %zd was used for some curl_off_t variables then only the lower
32-bits was read and the upper 32-bits would be read for part or all of
the next specifier.
Fixes https://github.com/curl/curl/issues/11327
Closes https://github.com/curl/curl/pull/11321
- Implement AUTH=+LOGIN for CURLOPT_LOGIN_OPTIONS to prefer plaintext
LOGIN over SASL auth.
Prior to this change there was no method to be able to fall back to
LOGIN if an IMAP server advertises SASL capabilities. However, this may
be desirable for e.g. a misconfigured server.
Per: https://www.ietf.org/rfc/rfc5092.html#section-3.2
";AUTH=<enc-auth-type>" looks to be the correct way to specify what
authenication method to use, regardless of SASL or not.
Closes https://github.com/curl/curl/pull/10041
- all: SEE ALSO the libcurl-ws man page
- send: add example and return value information
- meta: mention that the returned data is read-only
Closes#11318
`max_recv_speed` is `curl_off_t`, so using `size_t` might result in
-Wconversion GCC warnings for 32-bit `size_t`. Visible in the NetBSD
ARM autobuilds.
Closes https://github.com/curl/curl/pull/11312
