mirror of
https://sourceware.org/git/binutils-gdb.git
synced 2024-12-15 04:31:49 +08:00
264 lines
8.6 KiB
C
264 lines
8.6 KiB
C
/*
|
|
* Copyright (C) 1995 Advanced RISC Machines Limited. All rights reserved.
|
|
*
|
|
* This software may be freely used, copied, modified, and distributed
|
|
* provided that the above copyright notice is preserved in all copies of the
|
|
* software.
|
|
*/
|
|
|
|
/*-*-C-*-
|
|
*
|
|
* $Revision$
|
|
* $Date$
|
|
*
|
|
*
|
|
* Project: ANGEL
|
|
*
|
|
* Title: Definitions required for the rx and tx engines
|
|
*/
|
|
|
|
#ifndef angel_rxtx_h
|
|
#define angel_rxtx_h
|
|
|
|
|
|
/*
|
|
* we need a definition for bool, which is "system" dependent
|
|
*/
|
|
#ifdef TARGET
|
|
# include "angel.h"
|
|
#else
|
|
# include "host.h"
|
|
#endif
|
|
|
|
#include "devclnt.h"
|
|
|
|
/* return status codes for the rx engine */
|
|
typedef enum re_status {
|
|
RS_WAIT_PKT,
|
|
RS_IN_PKT,
|
|
RS_BAD_PKT,
|
|
RS_GOOD_PKT
|
|
} re_status;
|
|
|
|
/* return status codes for the tx engine */
|
|
typedef enum te_status {
|
|
TS_IDLE,
|
|
TS_IN_PKT,
|
|
TS_DONE_PKT
|
|
} te_status;
|
|
|
|
|
|
/*
|
|
* required serial definitions, they should all be <32, refer to the
|
|
* re_config struct comments for more details
|
|
*/
|
|
#define serial_STX (0x1c) /* data packet start */
|
|
#define serial_ETX (0x1d) /* packet end */
|
|
#define serial_ESC (0x1b) /* standard escape character */
|
|
#define serial_XON (0x11) /* software flow control - enable transmission */
|
|
#define serial_XOFF (0x13) /* software flow control - disable transmission */
|
|
|
|
/*
|
|
* All other characters are transmitted clean. If any of the above
|
|
* characters need to be transmitted as part of the serial data stream
|
|
* then the character will be preceded by the "serial_ESC" character,
|
|
* and then the required character transmitted (OR-ed with the
|
|
* "serial_ESCAPE" value, to ensure that the serial stream never has
|
|
* any of the exceptional characters generated by data transfers).
|
|
*/
|
|
|
|
#define serial_ESCAPE (0x40) /* OR-ed with escaped characters */
|
|
|
|
/* bad packet error codes */
|
|
typedef enum re_error {
|
|
RE_OKAY,
|
|
RE_U_STX,
|
|
RE_U_ETX,
|
|
RE_LEN,
|
|
RE_CRC,
|
|
RE_NETX,
|
|
RE_INTERNAL
|
|
} re_error;
|
|
|
|
/* a decoded packet */
|
|
struct data_packet {
|
|
unsigned short buf_len; /* should be set by caller */
|
|
DevChanID type; /* valid when status is RS_GOOD_PKT */
|
|
unsigned short len; /* --"-- */
|
|
unsigned int crc; /* crc for the unescaped pkt */
|
|
unsigned char *data; /* should be set by caller */
|
|
};
|
|
|
|
/*
|
|
* Purpose: typedef for flow control function
|
|
*
|
|
* Params:
|
|
* Input: fc_char the flow control character in question
|
|
* In/Out: cb_data callback data as set in the fc_data
|
|
* field of re_config, typically device id
|
|
*
|
|
* This callback would tpyically respond to received XON and XOFF
|
|
* characters by controlling the transmit side of the device.
|
|
*/
|
|
typedef void (*fc_cb_func)(char fc_char, void *cb_data);
|
|
|
|
|
|
/*
|
|
* Purpose: typedef for the function to alloc the data buffer
|
|
*
|
|
* Params:
|
|
* In/Out: packet the data packet: len and type will be set on
|
|
* entry, and buf_len and data should
|
|
* be set by this routine if successful.
|
|
* cb_data callback data as set in the ba_data
|
|
* field of re_config, typically device id
|
|
*
|
|
* Returns: TRUE buffer allocated okay
|
|
* FALSE couldn't allocate buffer of required size
|
|
* for given type
|
|
*
|
|
* This callback should attempt to acquire a buffer for the data portion
|
|
* of the packet which is currently being received, based on the len and
|
|
* type fields supplied in packet.
|
|
*
|
|
* angel_DD_RxEng_BufferAlloc() is supplied for use as this callback,
|
|
* and will be sufficient for most devices.
|
|
*/
|
|
typedef bool (*BufferAlloc_CB_Fn)(struct data_packet *packet, void *cb_data);
|
|
|
|
|
|
/*
|
|
* The static info needed by the engine, may vary per device.
|
|
*
|
|
* fc_set and esc_set are bitmaps, e.g. bit 3 == charcode 3 == ASCII ETX.
|
|
* Thus any of the first 32 charcodes can be set for flow control or to
|
|
* be escaped.
|
|
*
|
|
* Note that esc_set should include all of fc_set, and should have bits
|
|
* set for stx, etx and esc, as a minimum.
|
|
*
|
|
* If character codes > 31 need to be used then fc_set and esc_set
|
|
* and their handling can be extended to use arrays and bit manipulation
|
|
* macros, potentially up to the full 256 possible chars.
|
|
*
|
|
* Note too that this could/should be shared with the tx engine.
|
|
*/
|
|
|
|
struct re_config {
|
|
unsigned char stx; /* the STX char for this device */
|
|
unsigned char etx; /* the ETX --"-- */
|
|
unsigned char esc; /* the ESC --"-- */
|
|
unsigned int fc_set; /* bitmap of flow control chars */
|
|
unsigned int esc_set; /* bitmap of special chars */
|
|
fc_cb_func fc_callback; /* flow control callback func */
|
|
void *fc_data; /* data to pass to fc_callback */
|
|
BufferAlloc_CB_Fn ba_callback; /* buffer alloc callback */
|
|
void *ba_data; /* data to pass to ba_calback */
|
|
};
|
|
|
|
/* the dynamic info needed by the rx engine */
|
|
struct re_state {
|
|
unsigned char rx_state; /* 3 bits pkt state, 1 prepro state */
|
|
unsigned short field_c; /* chars left in current field */
|
|
unsigned short index; /* index into buffer */
|
|
unsigned int crc; /* crc accumulator */
|
|
re_error error; /* valid only if status is RS_BAD_PKT */
|
|
const struct re_config *config; /* pointer to static config */
|
|
};
|
|
|
|
/* dynamic state info needed by the tx engine */
|
|
struct te_state {
|
|
unsigned short field_c; /* position in current field */
|
|
unsigned char tx_state; /* encodes n,e, and f (2+1+2=5 bits) */
|
|
unsigned char encoded; /* escape-encoded char for transmission */
|
|
const struct re_config *config; /* pointer to static config */
|
|
unsigned int crc; /* space for CRC (before escaping) */
|
|
};
|
|
|
|
/*
|
|
* Function: Angel_RxEngineInit
|
|
* Purpose: Initialise state (during device init) for engine.
|
|
*
|
|
* Params:
|
|
* Input: config static config info
|
|
* In/Out: state internal state
|
|
*/
|
|
|
|
void Angel_RxEngineInit(const struct re_config *config,
|
|
struct re_state *state);
|
|
|
|
/*
|
|
* Function: Angel_RxEngine
|
|
* Purpose: Rx Engine for character-based devices
|
|
*
|
|
* Params:
|
|
* Input: new_ch the latest character
|
|
*
|
|
* In/Out: packet details of packet
|
|
* packet.buf_len and packet.data must
|
|
* be set on entry!
|
|
* state internal state, intially set by
|
|
* angel_RxEngineInit()
|
|
*
|
|
* Returns: re_status (see above)
|
|
*
|
|
*/
|
|
|
|
re_status Angel_RxEngine(unsigned char new_ch, struct data_packet *packet,
|
|
struct re_state *state);
|
|
|
|
/*
|
|
* This can be used as the buffer allocation callback for the rx engine,
|
|
* and will make use of angel_DD_GetBuffer() [in devdrv.h].
|
|
*
|
|
* Saves duplicating this callback function in every device driver that
|
|
* uses the rx engine.
|
|
*
|
|
* Note that this REQUIRES that the device id is installed as ba_data
|
|
* in the rx engine config structure for the driver.
|
|
*/
|
|
bool angel_DD_RxEng_BufferAlloc( struct data_packet *packet, void *cb_data );
|
|
|
|
/*
|
|
* Function: Angel_TxEngineInit
|
|
* Purpose: Set up tx engine at start of new packet, calculate CRC etc.
|
|
* (This should perform the actions described under
|
|
* "Initialisation" above)
|
|
*
|
|
* Params:
|
|
* Input: config static config info
|
|
* packet the packet to transmit
|
|
* In/Out: state internal state
|
|
*/
|
|
|
|
void Angel_TxEngineInit(const struct re_config *config,
|
|
const struct data_packet *packet,
|
|
struct te_state *state);
|
|
|
|
/*
|
|
* Function: Angel_TxEngine
|
|
* Purpose: Tx Engine for character-based devices
|
|
*
|
|
* Params:
|
|
* Input: packet details of packet
|
|
* packet.len, packet.data and
|
|
* packet.type must
|
|
* be set on entry!
|
|
* In/Out: state internal state, intially set by
|
|
* angel_TxEngineStart()
|
|
* Output: tx_ch the character to be transmitted
|
|
* (NOT SET if return code is TS_IDLE)
|
|
*
|
|
* Returns: te_status (see above)
|
|
*/
|
|
|
|
te_status Angel_TxEngine(const struct data_packet *packet,
|
|
struct te_state *state,
|
|
unsigned char *tx_ch);
|
|
|
|
|
|
|
|
#endif /* !defined(angel_rxtx_h) */
|
|
|
|
/* EOF rxtx.h */
|