mirror of
https://sourceware.org/git/binutils-gdb.git
synced 2024-12-27 04:52:05 +08:00
a2c5833233
The result of running etc/update-copyright.py --this-year, fixing all the files whose mode is changed by the script, plus a build with --enable-maintainer-mode --enable-cgen-maint=yes, then checking out */po/*.pot which we don't update frequently. The copy of cgen was with commit d1dd5fcc38ead reverted as that commit breaks building of bfp opcodes files.
265 lines
9.0 KiB
Plaintext
265 lines
9.0 KiB
Plaintext
@c Copyright (C) 1996-2022 Free Software Foundation, Inc.
|
|
@c This is part of the GAS manual.
|
|
@c For copying conditions, see the file as.texinfo.
|
|
@ifset GENERIC
|
|
@page
|
|
@node D10V-Dependent
|
|
@chapter D10V Dependent Features
|
|
@end ifset
|
|
@ifclear GENERIC
|
|
@node Machine Dependencies
|
|
@chapter D10V Dependent Features
|
|
@end ifclear
|
|
|
|
@cindex D10V support
|
|
@menu
|
|
* D10V-Opts:: D10V Options
|
|
* D10V-Syntax:: Syntax
|
|
* D10V-Float:: Floating Point
|
|
* D10V-Opcodes:: Opcodes
|
|
@end menu
|
|
|
|
@node D10V-Opts
|
|
@section D10V Options
|
|
@cindex options, D10V
|
|
@cindex D10V options
|
|
The Mitsubishi D10V version of @code{@value{AS}} has a few machine
|
|
dependent options.
|
|
|
|
@table @samp
|
|
@item -O
|
|
The D10V can often execute two sub-instructions in parallel. When this option
|
|
is used, @code{@value{AS}} will attempt to optimize its output by detecting when
|
|
instructions can be executed in parallel.
|
|
@item --nowarnswap
|
|
To optimize execution performance, @code{@value{AS}} will sometimes swap the
|
|
order of instructions. Normally this generates a warning. When this option
|
|
is used, no warning will be generated when instructions are swapped.
|
|
@item --gstabs-packing
|
|
@itemx --no-gstabs-packing
|
|
@code{@value{AS}} packs adjacent short instructions into a single packed
|
|
instruction. @samp{--no-gstabs-packing} turns instruction packing off if
|
|
@samp{--gstabs} is specified as well; @samp{--gstabs-packing} (the
|
|
default) turns instruction packing on even when @samp{--gstabs} is
|
|
specified.
|
|
@end table
|
|
|
|
@node D10V-Syntax
|
|
@section Syntax
|
|
@cindex D10V syntax
|
|
@cindex syntax, D10V
|
|
|
|
The D10V syntax is based on the syntax in Mitsubishi's D10V architecture manual.
|
|
The differences are detailed below.
|
|
|
|
@menu
|
|
* D10V-Size:: Size Modifiers
|
|
* D10V-Subs:: Sub-Instructions
|
|
* D10V-Chars:: Special Characters
|
|
* D10V-Regs:: Register Names
|
|
* D10V-Addressing:: Addressing Modes
|
|
* D10V-Word:: @@WORD Modifier
|
|
@end menu
|
|
|
|
|
|
@node D10V-Size
|
|
@subsection Size Modifiers
|
|
@cindex D10V size modifiers
|
|
@cindex size modifiers, D10V
|
|
The D10V version of @code{@value{AS}} uses the instruction names in the D10V
|
|
Architecture Manual. However, the names in the manual are sometimes ambiguous.
|
|
There are instruction names that can assemble to a short or long form opcode.
|
|
How does the assembler pick the correct form? @code{@value{AS}} will always pick the
|
|
smallest form if it can. When dealing with a symbol that is not defined yet when a
|
|
line is being assembled, it will always use the long form. If you need to force the
|
|
assembler to use either the short or long form of the instruction, you can append
|
|
either @samp{.s} (short) or @samp{.l} (long) to it. For example, if you are writing
|
|
an assembly program and you want to do a branch to a symbol that is defined later
|
|
in your program, you can write @samp{bra.s foo}.
|
|
Objdump and GDB will always append @samp{.s} or @samp{.l} to instructions which
|
|
have both short and long forms.
|
|
|
|
@node D10V-Subs
|
|
@subsection Sub-Instructions
|
|
@cindex D10V sub-instructions
|
|
@cindex sub-instructions, D10V
|
|
The D10V assembler takes as input a series of instructions, either one-per-line,
|
|
or in the special two-per-line format described in the next section. Some of these
|
|
instructions will be short-form or sub-instructions. These sub-instructions can be packed
|
|
into a single instruction. The assembler will do this automatically. It will also detect
|
|
when it should not pack instructions. For example, when a label is defined, the next
|
|
instruction will never be packaged with the previous one. Whenever a branch and link
|
|
instruction is called, it will not be packaged with the next instruction so the return
|
|
address will be valid. Nops are automatically inserted when necessary.
|
|
|
|
If you do not want the assembler automatically making these decisions, you can control
|
|
the packaging and execution type (parallel or sequential) with the special execution
|
|
symbols described in the next section.
|
|
|
|
@node D10V-Chars
|
|
@subsection Special Characters
|
|
@cindex line comment character, D10V
|
|
@cindex D10V line comment character
|
|
A semicolon (@samp{;}) can be used anywhere on a line to start a
|
|
comment that extends to the end of the line.
|
|
|
|
If a @samp{#} appears as the first character of a line, the whole line
|
|
is treated as a comment, but in this case the line could also be a
|
|
logical line number directive (@pxref{Comments}) or a preprocessor
|
|
control command (@pxref{Preprocessing}).
|
|
|
|
@cindex sub-instruction ordering, D10V
|
|
@cindex D10V sub-instruction ordering
|
|
Sub-instructions may be executed in order, in reverse-order, or in parallel.
|
|
Instructions listed in the standard one-per-line format will be executed sequentially.
|
|
To specify the executing order, use the following symbols:
|
|
@table @samp
|
|
@item ->
|
|
Sequential with instruction on the left first.
|
|
@item <-
|
|
Sequential with instruction on the right first.
|
|
@item ||
|
|
Parallel
|
|
@end table
|
|
The D10V syntax allows either one instruction per line, one instruction per line with
|
|
the execution symbol, or two instructions per line. For example
|
|
@table @code
|
|
@item abs a1 -> abs r0
|
|
Execute these sequentially. The instruction on the right is in the right
|
|
container and is executed second.
|
|
@item abs r0 <- abs a1
|
|
Execute these reverse-sequentially. The instruction on the right is in the right
|
|
container, and is executed first.
|
|
@item ld2w r2,@@r8+ || mac a0,r0,r7
|
|
Execute these in parallel.
|
|
@item ld2w r2,@@r8+ ||
|
|
@itemx mac a0,r0,r7
|
|
Two-line format. Execute these in parallel.
|
|
@item ld2w r2,@@r8+
|
|
@itemx mac a0,r0,r7
|
|
Two-line format. Execute these sequentially. Assembler will
|
|
put them in the proper containers.
|
|
@item ld2w r2,@@r8+ ->
|
|
@itemx mac a0,r0,r7
|
|
Two-line format. Execute these sequentially. Same as above but
|
|
second instruction will always go into right container.
|
|
@end table
|
|
@cindex symbol names, @samp{$} in
|
|
@cindex @code{$} in symbol names
|
|
Since @samp{$} has no special meaning, you may use it in symbol names.
|
|
|
|
@node D10V-Regs
|
|
@subsection Register Names
|
|
@cindex D10V registers
|
|
@cindex registers, D10V
|
|
You can use the predefined symbols @samp{r0} through @samp{r15} to refer to the D10V
|
|
registers. You can also use @samp{sp} as an alias for @samp{r15}. The accumulators
|
|
are @samp{a0} and @samp{a1}. There are special register-pair names that may
|
|
optionally be used in opcodes that require even-numbered registers. Register names are
|
|
not case sensitive.
|
|
|
|
Register Pairs
|
|
@table @code
|
|
@item r0-r1
|
|
@item r2-r3
|
|
@item r4-r5
|
|
@item r6-r7
|
|
@item r8-r9
|
|
@item r10-r11
|
|
@item r12-r13
|
|
@item r14-r15
|
|
@end table
|
|
|
|
The D10V also has predefined symbols for these control registers and status bits:
|
|
@table @code
|
|
@item psw
|
|
Processor Status Word
|
|
@item bpsw
|
|
Backup Processor Status Word
|
|
@item pc
|
|
Program Counter
|
|
@item bpc
|
|
Backup Program Counter
|
|
@item rpt_c
|
|
Repeat Count
|
|
@item rpt_s
|
|
Repeat Start address
|
|
@item rpt_e
|
|
Repeat End address
|
|
@item mod_s
|
|
Modulo Start address
|
|
@item mod_e
|
|
Modulo End address
|
|
@item iba
|
|
Instruction Break Address
|
|
@item f0
|
|
Flag 0
|
|
@item f1
|
|
Flag 1
|
|
@item c
|
|
Carry flag
|
|
@end table
|
|
|
|
@node D10V-Addressing
|
|
@subsection Addressing Modes
|
|
@cindex addressing modes, D10V
|
|
@cindex D10V addressing modes
|
|
@code{@value{AS}} understands the following addressing modes for the D10V.
|
|
@code{R@var{n}} in the following refers to any of the numbered
|
|
registers, but @emph{not} the control registers.
|
|
@table @code
|
|
@item R@var{n}
|
|
Register direct
|
|
@item @@R@var{n}
|
|
Register indirect
|
|
@item @@R@var{n}+
|
|
Register indirect with post-increment
|
|
@item @@R@var{n}-
|
|
Register indirect with post-decrement
|
|
@item @@-SP
|
|
Register indirect with pre-decrement
|
|
@item @@(@var{disp}, R@var{n})
|
|
Register indirect with displacement
|
|
@item @var{addr}
|
|
PC relative address (for branch or rep).
|
|
@item #@var{imm}
|
|
Immediate data (the @samp{#} is optional and ignored)
|
|
@end table
|
|
|
|
@node D10V-Word
|
|
@subsection @@WORD Modifier
|
|
@cindex D10V @@word modifier
|
|
@cindex @@word modifier, D10V
|
|
Any symbol followed by @code{@@word} will be replaced by the symbol's value
|
|
shifted right by 2. This is used in situations such as loading a register
|
|
with the address of a function (or any other code fragment). For example, if
|
|
you want to load a register with the location of the function @code{main} then
|
|
jump to that function, you could do it as follows:
|
|
@smallexample
|
|
@group
|
|
ldi r2, main@@word
|
|
jmp r2
|
|
@end group
|
|
@end smallexample
|
|
|
|
@node D10V-Float
|
|
@section Floating Point
|
|
@cindex floating point, D10V
|
|
@cindex D10V floating point
|
|
The D10V has no hardware floating point, but the @code{.float} and @code{.double}
|
|
directives generates @sc{ieee} floating-point numbers for compatibility
|
|
with other development tools.
|
|
|
|
@node D10V-Opcodes
|
|
@section Opcodes
|
|
@cindex D10V opcode summary
|
|
@cindex opcode summary, D10V
|
|
@cindex mnemonics, D10V
|
|
@cindex instruction summary, D10V
|
|
For detailed information on the D10V machine instruction set, see
|
|
@cite{D10V Architecture: A VLIW Microprocessor for Multimedia Applications}
|
|
(Mitsubishi Electric Corp.).
|
|
@code{@value{AS}} implements all the standard D10V opcodes. The only changes are those
|
|
described in the section on size modifiers
|
|
|