Add ASMACRO instruction support as per the MIPS16e ASE architecture
specifications [1][2], completing MIPS16e instruction set support.
[1] "MIPS32 Architecture for Programmers, Volume IV-a: The MIPS16e
Application-Specific Extension to the MIPS32 Architecture", MIPS
Technologies, Inc., Document Number: MD00076, Revision 2.63, July
16, 2013, Section 4.1 "MIPS16e Instruction Descriptions", p. 65
[2] "MIPS64 Architecture for Programmers, Volume IV-a: The MIPS16e
Application-Specific Extension to the MIPS64 Architecture", MIPS
Technologies, Inc., Document Number: MD00077, Revision 2.60, June
25, 2008, Section 1.1 "MIPS16e Instruction Descriptions", p. 66
include/
* opcode/mips.h: Document `0', `1', `2', `3', `4' and `s'
operand codes.
opcodes/
* mips16-opc.c (decode_mips16_operand): Add `0', `1', `2', `3',
`4' and `s' operand codes.
(mips16_opcodes): Add "asmacro" entry.
binutils/
* testsuite/binutils-all/mips/mips16-extend-insn.d: Update for
ASMACRO support.
gas/
* testsuite/gas/mips/mips16-asmacro.d: New test.
* testsuite/gas/mips/mips16-32@mips16-asmacro.d: New test.
* testsuite/gas/mips/mips16-64@mips16-asmacro.d: New test.
* testsuite/gas/mips/mips16-asmacro.s: New test source.
* testsuite/gas/mips/mips.exp: Run the new tests.
Replace `0' and `4' operand codes with `.' and `F' respectively to free
up the `0'-`4' consecutive range. No functional change.
gas/
* config/tc-mips.c (mips16_macro_build): Replace `0' and `4'
operand codes with `.' and `F' respectively.
(mips16_macro): Likewise.
include/
* opcode/mips.h: Replace `0' and `4' operand codes with `.' and
`F' respectively.
opcodes/
* mips16-opc.c (decode_mips16_operand): Replace `0' and `4'
operand codes with `.' and `F' respectively.
(mips16_opcodes): Likewise.
Identify non-extensible instructions in the MIPS16 opcode table and
disallow their use with the `.e' instruction size suffix in assembly and
do not interpret any EXTEND prefix present as a part of the instruction
in disassembly.
According to all versions of the MIPS16 ASE specifications the following
instructions encodings are not extensible [1][2][3][4][5][6]: I8/MOV32R,
I8/MOVR32, all RRR minor opcodes, all RR minor opcodes except from DSRA
and DSRL, and EXTEND itself, and as from revision 2.50 of the MIPS16e
ASE specifications it has been further clarified what was previously
implied, that non-extesiable instructions when preceded with an EXTEND
prefix must cause a Reserved Instruction exception [3][5].
Therefore in the presence of an EXTEND prefix none of these instructions
are supposed to be handled as extended instructions and supporting these
forms in disassembly causes confusion, and in the case of the RRR major
opcode it also clashes with the ASMACRO encoding.
References:
[1] "Product Description, MIPS16 Application-Specific Extension",
Version 1.3, MIPS Technologies, Inc., 970130, Table 3. "MIPS16
Instruction Set Summary", p. 5
[2] same, Table 5 "RR Minor Opcodes (RR-type instructions)", p.10
[3] "MIPS32 Architecture for Programmers, Volume IV-a: The MIPS16e
Application-Specific Extension to the MIPS32 Architecture", MIPS
Technologies, Inc., Document Number: MD00076, Revision 2.63, July
16, 2013, Section 3.9 "MIPS16e Instruction Summaries", pp. 37-39
[4] same, Section 3.15 "Instruction Bit Encoding", pp. 46-49
[5] "MIPS64 Architecture for Programmers, Volume IV-a: The MIPS16e
Application-Specific Extension to the MIPS64 Architecture", MIPS
Technologies, Inc., Document Number: MD00077, Revision 2.60, June
25, 2008, Section 1.9 "MIPS16e Instruction Summaries", pp. 38-41
[6] same, Section 1.15 "Instruction Bit Encoding", pp. 48-51
include/
* opcode/mips.h (INSN2_SHORT_ONLY): New macro.
gas/
* config/tc-mips.c (is_size_valid_16): Disallow a `.e' suffix
instruction size override for INSN2_SHORT_ONLY opcode table
entries.
* testsuite/gas/mips/mips16-extend-swap.d: Adjust output.
* testsuite/gas/mips/mips16-macro-e.l: Adjust error messages.
* testsuite/gas/mips/mips16-32@mips16-macro-e.l: Adjust error
messages.
* testsuite/gas/mips/mips16e-32@mips16-macro-e.l: Adjust error
messages.
* testsuite/gas/mips/mips16-insn-e.d: New test.
* testsuite/gas/mips/mips16-insn-t.d: New test.
* testsuite/gas/mips/mips16-32@mips16-insn-e.d: New test.
* testsuite/gas/mips/mips16-64@mips16-insn-e.d: New test.
* testsuite/gas/mips/mips16e-32@mips16-insn-e.d: New test.
* testsuite/gas/mips/mips16-32@mips16-insn-t.d: New test.
* testsuite/gas/mips/mips16-64@mips16-insn-t.d: New test.
* testsuite/gas/mips/mips16e-32@mips16-insn-t.d: New test.
* testsuite/gas/mips/mips16-insn-e.l: New stderr output.
* testsuite/gas/mips/mips16-insn-t.l: New stderr output.
* testsuite/gas/mips/mips16-32@mips16-insn-e.l: New stderr
output.
* testsuite/gas/mips/mips16-64@mips16-insn-e.l: New stderr
output.
* testsuite/gas/mips/mips16e-32@mips16-insn-e.l: New stderr
output.
* testsuite/gas/mips/mips16-32@mips16-insn-t.l: New stderr
output.
* testsuite/gas/mips/mips16-64@mips16-insn-t.l: New stderr
output.
* testsuite/gas/mips/mips16e-32@mips16-insn-t.l: New stderr
output.
* testsuite/gas/mips/mips16-insn-e.s: New test source.
* testsuite/gas/mips/mips16-insn-t.s: New test source.
* testsuite/gas/mips/mips.exp: Run the new tests.
opcodes/
* mips-dis.c (print_insn_mips16): Disallow EXTEND prefix
matching for INSN2_SHORT_ONLY opcode table entries.
* mips16-opc.c (SH): New macro.
(mips16_opcodes): Set SH in `pinfo2' for non-extensible
instruction entries: "nop", "addu", "and", "break", "cmp",
"daddu", "ddiv", "ddivu", "div", "divu", "dmult", "dmultu",
"drem", "dremu", "dsllv", "dsll", "dsrav", "dsra", "dsrlv",
"dsrl", "dsubu", "exit", "entry", "jalr", "jal", "jr", "j",
"jalrc", "jrc", "mfhi", "mflo", "move", "mult", "multu", "neg",
"not", "or", "rem", "remu", "sllv", "sll", "slt", "sltu",
"srav", "sra", "srlv", "srl", "subu", "xor", "sdbbp", "seb",
"seh", "sew", "zeb", "zeh", "zew" and "extend".
binutils/
* testsuite/binutils-all/mips/mips16-extend-insn.d: New test.
* testsuite/binutils-all/mips/mips16-extend-insn.s: New test
source.
* testsuite/binutils-all/mips/mips.exp: Run the new tests.
Switch to 32-bit MIPS16 opcode table entry interpretation, similar to
how the microMIPS opcode table is handled, for both the `match' and
`mask' fields, removing special casing for JAL and JALX instructions and
their `a' and `i' operand codes throughout, while retaining automatic
processing of extendable opcodes in assembly and disassembly.
In assembly disallow size enforcement suffixes as appropriate: `.t' for
both 32-bit instructions and macros and `.e' for macros only, making
macro handling consistent with the microMIPS instruction set.
In disassembly fully decode EXTEND prefixes prepended to unsupported
instruction encodings (according to the ISA selection) rather than
dumping them as hexadecimal data along with the following instruction,
removing all special casing for the EXTEND prefix and making its
handling rely on its opcode table entry, except where it is considered a
part of an extendable instruction.
include/
* opcode/mips.h (mips_opcode_32bit_p): New inline function.
gas/
* config/tc-mips.c (micromips_insn_length): Use
`mips_opcode_32bit_p'.
(is_size_valid): Adjust description.
(is_size_valid_16): New function.
(validate_mips_insn): Use `mips_opcode_32bit_p' in MIPS16
operand decoding.
(validate_mips16_insn): Remove `a' and `i' operand code special
casing, use `mips_opcode_32bit_p' to determine instruction
width.
(append_insn): Adjust forced MIPS16 instruction size
determination.
(match_mips16_insn): Likewise. Don't shift the instruction's
opcode with the `a' and `i' operand codes. Use
`mips_opcode_32bit_p' in operand decoding.
(match_mips16_insns): Check for forced instruction size's
validity.
(mips16_ip): Don't force instruction size in the `noautoextend'
mode.
* testsuite/gas/mips/mips16-jal-e.d: New test.
* testsuite/gas/mips/mips16-jal-t.d: New test.
* testsuite/gas/mips/mips16-macro-e.d: New test.
* testsuite/gas/mips/mips16-macro-t.d: New test.
* testsuite/gas/mips/mips16-jal-t.l: New stderr output.
* testsuite/gas/mips/mips16-macro-e.l: New stderr output.
* testsuite/gas/mips/mips16-macro-t.l: New stderr output.
* testsuite/gas/mips/mips16-jal-e.s: New test source.
* testsuite/gas/mips/mips16-jal-t.s: New test source.
* testsuite/gas/mips/mips16-macro-e.s: New test source.
* testsuite/gas/mips/mips16-macro-t.s: New test source.
* testsuite/gas/mips/mips.exp: Run the new tests.
opcodes/
* mips-dis.c (print_mips16_insn_arg): Always handle `extend' and
`insn' together, with `extend' as the high-order 16 bits.
(match_kind): New enum.
(print_insn_mips16): Rework for 32-bit instruction matching.
Do not dump EXTEND prefixes here.
* mips16-opc.c (mips16_opcodes): Move "extend" entry to the end.
Recode `match' and `mask' fields as 32-bit in absolute "jal" and
"jalx" entries.
binutils/
* testsuite/binutils-all/mips/mips16-extend-noinsn.d: Adjust
test for separate EXTEND prefix disassembly.
This code has never been used throughout the repository history, and
likely not before either, as due to the assymetry of MIPS16 instruction
set encoding there are no 32-bit shift operations having their immediate
shift count placed in the position of the usual `rx' instruction field.
gas/
* config/tc-mips.c (mips16_macro_build) <'>'>: Remove case.
include/
* opcode/mips.h: Remove references to `>' operand code.
opcodes/
* mips16-opc.c (decode_mips16_operand) <'>'>: Remove cases.
binutils:
2014-10-31 Andrew Pinski <apinski@cavium.com>
Naveen H.S <Naveen.Hurugalawadi@caviumnetworks.com>
* readelf.c (print_mips_isa_ext): Print the value of Octeon3.
gas:
2014-10-31 Andrew Pinski <apinski@cavium.com>
Naveen H.S <Naveen.Hurugalawadi@caviumnetworks.com>
* config/tc-mips.c (CPU_IS_OCTEON): Handle CPU_OCTEON3.
(mips_cpu_info_table): Octeon3 enables virt ase.
* doc/c-mips.texi: Document octeon3 as an acceptable value for
-march=.
gas/testsuite:
2014-10-31 Andrew Pinski <apinski@cavium.com>
Naveen H.S <Naveen.Hurugalawadi@caviumnetworks.com>
* gas/mips/mips.exp: Add support for Octeon3 architecture.
Also add in support for running Octeon3 tests.
* gas/mips/octeon3.d: New test.
* gas/mips/octeon3.s: New test source.
opcodes:
2014-10-31 Andrew Pinski <apinski@cavium.com>
Naveen H.S <Naveen.Hurugalawadi@caviumnetworks.com>
* mips-dis.c (mips_arch_choices): Add octeon3.
* mips-opc.c (IOCT): Include INSN_OCTEON3.
(IOCT2): Likewise.
(IOCT3): New define.
(IVIRT): New define.
(mips_builtin_opcodes): Add dmfgc0, dmtgc0, hypcall, mfgc0, mtgc0,
tlbinv, tlbinvf, tlbgr, tlbgwi, tlbginv, tlbginvf, tlbgwr, tlbgp, tlti
IVIRT instructions.
Extend mtm0, mtm1, mtm2, mtp0, mtp1, mtp2 instructions to take another
operand for IOCT3.
bfd:
2014-10-31 Andrew Pinski <apinski@cavium.com>
Naveen H.S <Naveen.Hurugalawadi@caviumnetworks.com>
* archures.c: Add octeon3 for mips target.
* bfd-in2.h: Regenerate.
* bfd/cpu-mips.c: Define I_mipsocteon3.
nfo_struct): Add octeon3 support.
* bfd/elfxx-mips.c: (_bfd_elf_mips_mach): Add support for
octeon3.
(mips_set_isa_flags): Add support for octeon3.
(bfd_mips_isa_ext): Add bfd_mach_mips_octeon3.
(mips_mach_extensions): Make bfd_mach_mips_octeon3 an
extension of bfd_mach_mips_octeon2.
(print_mips_isa_ext): Print the value of Octeon3.
bfd/
* aoutx.h (NAME (aout, machine_type)): Add mips32r6 and mips64r6.
* archures.c (bfd_architecture): Likewise.
* bfd-in2.h (bfd_architecture): Likewise.
(bfd_reloc_code_real): Add relocs BFD_RELOC_MIPS_21_PCREL_S2,
BFD_RELOC_MIPS_26_PCREL_S2, BFD_RELOC_MIPS_18_PCREL_S3 and
BFD_RELOC_MIPS_19_PCREL_S2.
* cpu-mips.c (arch_info_struct): Add mips32r6 and mips64r6.
* elf32-mips.c: Define relocs R_MIPS_PC21_S2, R_MIPS_PC26_S2
R_MIPS_PC18_S3, R_MIPS_PC19_S2, R_MIPS_PCHI16 and R_MIPS_PCLO16.
(mips_reloc_map): Add entries for BFD_RELOC_MIPS_21_PCREL_S2,
BFD_RELOC_MIPS_26_PCREL_S2, BFD_RELOC_MIPS_18_PCREL_S3,
BFD_RELOC_MIPS_19_PCREL_S2, BFD_RELOC_HI16_S_PCREL and
BFD_RELOC_LO16_PCREL.
* elf64-mips.c: Define REL, and RELA relocations R_MIPS_PC21_S2,
R_MIPS_PC26_S2, R_MIPS_PC18_S3, R_MIPS_PC19_S2, R_MIPS_PCHI16
and R_MIPS_PCLO16.
(mips_reloc_map): Add entries for BFD_RELOC_MIPS_21_PCREL_S2,
BFD_RELOC_MIPS_26_PCREL_S2, BFD_RELOC_MIPS_18_PCREL_S3,
BFD_RELOC_MIPS_19_PCREL_S2, BFD_RELOC_HI16_S_PCREL and
BFD_RELOC_LO16_PCREL.
* elfn32-mips.c: Likewise.
* elfxx-mips.c (MIPSR6_P): New define.
(mipsr6_exec_plt_entry): New array.
(hi16_reloc_p): Add support for R_MIPS_PCHI16.
(lo16_reloc_p): Add support for R_MIPS_PCLO16.
(aligned_pcrel_reloc_p): New function.
(mips_elf_relocation_needs_la25_stub): Add support for relocs:
R_MIPS_PC21_S2 and R_MIPS_PC26_S2.
(mips_elf_calculate_relocation): Add support for relocs:
R_MIPS_PC21_S2, R_MIPS_PC26_S2, R_MIPS_PC18_S3, R_MIPS_PC19_S2,
R_MIPS_PCHI16 and R_MIPS_PCLO16.
(_bfd_elf_mips_mach): Add support for mips32r6 and mips64r6.
(mips_elf_add_lo16_rel_addend): Add support for R_MIPS_PCHI16.
(_bfd_mips_elf_check_relocs): Add support for relocs:
R_MIPS_PC21_S2 and R_MIPS_PC26_S2.
(_bfd_mips_elf_relocate_section): Add a check for unaligned
pc relative relocs.
(_bfd_mips_elf_finish_dynamic_symbol): Add support for MIPS r6
plt entry.
(mips_set_isa_flags): Add support for mips32r6 and mips64r6.
(_bfd_mips_elf_print_private_bfd_data): Likewise.
(mips_32bit_flags_p): Add support for mips32r6.
* libbfd.h (bfd_reloc_code_real_names): Add entries for
BFD_RELOC_MIPS_21_PCREL_S2, BFD_RELOC_MIPS_26_PCREL_S2,
BFD_RELOC_MIPS_18_PCREL_S3 and BFD_RELOC_MIPS_19_PCREL_S2.
* reloc.c: Document relocs BFD_RELOC_MIPS_21_PCREL_S2,
BFD_RELOC_MIPS_26_PCREL_S2, BFD_RELOC_MIPS_18_PCREL_S3 and
BFD_RELOC_MIPS_19_PCREL_S2.
binutils/
* readelf.c (get_machine_flags): Add support for mips32r6 and
mips64r6.
elfcpp/
* mips.h (E_MIPS_ARCH_32R6, E_MIPS_ARCH_64R6): New enum constants.
gas/
* config/tc-mips.c (mips_nan2008): New static global.
(mips_flag_nan2008): Removed.
(LL_SC_FMT): New define.
(COP12_FMT): Updated.
(ISA_IS_R6): New define.
(ISA_HAS_64BIT_REGS): Add mips64r6.
(ISA_HAS_DROR): Likewise.
(ISA_HAS_64BIT_FPRS): Add mips32r6 and mips64r6.
(ISA_HAS_ROR): Likewise.
(ISA_HAS_ODD_SINGLE_FPR): Likewise.
(ISA_HAS_MXHC1): Likewise.
(hilo_interlocks): Likewise.
(md_longopts): Likewise.
(ISA_HAS_LEGACY_NAN): New define.
(options): Add OPTION_MIPS32R6 and OPTION_MIPS64R6.
(mips_ase): Add field rem_rev.
(mips_ases): Updated to add which ISA an ASE was removed in.
(mips_isa_rev): Add support for mips32r6 and mips64r6.
(mips_check_isa_supports_ase): Add support to check if an ASE
has been removed in the specified MIPS ISA revision.
(validate_mips_insn): Skip '-' character.
(macro_build): Likewise.
(mips_check_options): Prevent R6 working with fp32, mips16,
micromips, or branch relaxation.
(file_mips_check_options): Set R6 floating point registers to
64 bit. Also deal with the nan2008 option.
(limited_pcrel_reloc_p): Add relocs: BFD_RELOC_MIPS_21_PCREL_S2,
BFD_RELOC_MIPS_26_PCREL_S2, BFD_RELOC_MIPS_18_PCREL_S3,
BFD_RELOC_MIPS_19_PCREL_S2, BFD_RELOC_HI16_S_PCREL and
BFD_RELOC_LO16_PCREL.
(operand_reg_mask): Add support for OP_SAME_RS_RT, OP_CHECK_PREV
and OP_NON_ZERO_REG.
(match_check_prev_operand): New static function.
(match_same_rs_rt_operand): New static function.
(match_non_zero_reg_operand): New static function.
(match_operand): Added entries for: OP_SAME_RS_RT, OP_CHECK_PREV
and OP_NON_ZERO_REG.
(insns_between): Added case to deal with forbidden slots.
(append_insn): Added support for relocs: BFD_RELOC_MIPS_21_PCREL_S2
and BFD_RELOC_MIPS_26_PCREL_S2.
(match_insn): Add support for operands -A, -B, +' and +". Also
skip '-' character.
(mips_percent_op): Add entries for %pcrel_hi and %pcrel_lo.
(md_parse_option): Add support for mips32r6 and mips64r6. Also
update the nan option handling.
(md_pcrel_from): Add cases for relocs: BFD_RELOC_MIPS_21_PCREL_S2,
BFD_RELOC_MIPS_26_PCREL_S2.
(mips_force_relocation): Prevent forced relaxation for MIPS r6.
(md_apply_fix): Add support for relocs: BFD_RELOC_MIPS_21_PCREL_S2,
BFD_RELOC_MIPS_26_PCREL_S2, BFD_RELOC_MIPS_18_PCREL_S3,
BFD_RELOC_MIPS_19_PCREL_S2, BFD_RELOC_HI16_S_PCREL and
BFD_RELOC_LO16_PCREL.
(s_mipsset): Add support for mips32r6 and mips64r6.
(s_nan): Update to support the new nan2008 framework.
(tc_gen_reloc): Add relocs: BFD_RELOC_MIPS_21_PCREL_S2,
BFD_RELOC_MIPS_26_PCREL_S2, BFD_RELOC_MIPS_18_PCREL_S3,
BFD_RELOC_MIPS_19_PCREL_S2, BFD_RELOC_HI16_S_PCREL and
BFD_RELOC_LO16_PCREL.
(mips_elf_final_processing): Updated to use the mips_nan2008.
(mips_cpu_info_table): Add entries for mips32r6 and mips64r6.
(macro): Enable ldc2, sdc2, ll, lld, swc2, sc, scd, cache, pref
macros for R6.
(mips_fix_adjustable): Make PC relative R6 relocations relative
to the symbol and not the section.
* configure.ac: Add support for mips32r6 and mips64r6.
* configure: Regenerate.
* doc/c-mips.texi: Document the -mips32r6 and -mips64r6 command line
options.
* doc/as.texinfo: Likewise.
gas/testsuite/
* gas/mips/24k-triple-stores-1.s: If testing for r6 prevent
non-supported instructions from being tested.
* gas/mips/24k-triple-stores-2.s: Likewise.
* gas/mips/24k-triple-stores-3.s: Likewise.
* gas/mips/24k-triple-stores-6.s: Likewise.
* gas/mips/beq.s: Likewise.
* gas/mips/eva.s: Likewise.
* gas/mips/ld-zero-3.s: Likewise.
* gas/mips/mips32-cp2.s: Likewise.
* gas/mips/mips32.s: Likewise.
* gas/mips/mips4.s: Likewise.
* gas/mips/add.s: Don't test the add instructions if r6, and
add padding.
* gas/mips/add.d: Check for a triple dot not a nop at the end of the
disassembly output.
* gas/mips/micromips@add.d: Likewise.
* gas/mips/mipsr6@24k-branch-delay-1.d: New file.
* gas/mips/mipsr6@24k-triple-stores-1.d: New file.
* gas/mips/mipsr6@24k-triple-stores-2-llsc.d: New file.
* gas/mips/mipsr6@24k-triple-stores-2.d: New file.
* gas/mips/mipsr6@24k-triple-stores-3.d: New file.
* gas/mips/mipsr6@24k-triple-stores-6.d: New file.
* gas/mips/mipsr6@add.d: New file.
* gas/mips/mipsr6@attr-gnu-4-1-msingle-float.l: New file.
* gas/mips/mipsr6@attr-gnu-4-1-msingle-float.s: New file.
* gas/mips/mipsr6@attr-gnu-4-1-msoft-float.l: New file.
* gas/mips/mipsr6@attr-gnu-4-1-msoft-float.s: New file.
* gas/mips/mipsr6@attr-gnu-4-2-mdouble-float.l: New file.
* gas/mips/mipsr6@attr-gnu-4-2-mdouble-float.s: New file.
* gas/mips/mipsr6@beq.d: New file.
* gas/mips/mipsr6@bge.d: New file.
* gas/mips/mipsr6@bgeu.d: New file.
* gas/mips/mipsr6@blt.d: New file.
* gas/mips/mipsr6@bltu.d: New file.
* gas/mips/mipsr6@branch-misc-1.d: New file.
* gas/mips/mipsr6@branch-misc-2-64.d: New file.
* gas/mips/mipsr6@branch-misc-2pic-64.d: New file.
* gas/mips/mipsr6@branch-misc-4-64.d: New file.
* gas/mips/mipsr6@cache.d: New file.
* gas/mips/mipsr6@eva.d: New file.
* gas/mips/mipsr6@jal-svr4pic-noreorder.d: New file.
* gas/mips/mipsr6@jal-svr4pic.d: New file.
* gas/mips/mipsr6@ld-zero-2.d: New file.
* gas/mips/mipsr6@ld-zero-3.d: New file.
* gas/mips/mipsr6@loc-swap-dis.d: New file.
* gas/mips/mipsr6@mips32-cp2.d: New file.
* gas/mips/mipsr6@mips32-imm.d: New file.
* gas/mips/mipsr6@mips32.d: New file.
* gas/mips/mipsr6@mips32r2.d: New file.
* gas/mips/mipsr6@mips4-fp.d: New file.
* gas/mips/mipsr6@mips4-fp.l: New file.
* gas/mips/mipsr6@mips4-fp.s: New file.
* gas/mips/mipsr6@mips4.d: New file.
* gas/mips/mipsr6@mips5-fp.d: New file.
* gas/mips/mipsr6@mips5-fp.l: New file.
* gas/mips/mipsr6@mips5-fp.s: New file.
* gas/mips/mipsr6@mips64.d: New file.
* gas/mips/mipsr6@msa-branch.d: New file.
* gas/mips/mipsr6@msa.d: New file.
* gas/mips/mipsr6@pref.d: New file.
* gas/mips/mipsr6@relax-swap3.d: New file.
* gas/mips/r6-64-n32.d: New file.
* gas/mips/r6-64-n64.d: New file.
* gas/mips/r6-64-removed.l: New file.
* gas/mips/r6-64-removed.s: New file.
* gas/mips/r6-64.s: New file.
* gas/mips/r6-attr-none-double.d: New file.
* gas/mips/r6-n32.d: New file.
* gas/mips/r6-n64.d: New file.
* gas/mips/r6-removed.l: New file.
* gas/mips/r6-removed.s: New file.
* gas/mips/r6.d: New file.
* gas/mips/r6.s: New file.
* gas/mips/mipsr6@mips32-dsp.d: New file.
* gas/mips/mipsr6@mips32-dspr2.d: New file.
* gas/mips/mipsr6@mips32r2-ill.l: New file.
* gas/mips/mipsr6@mips32r2-ill.s: New file.
* gas/mips/cache.s: Add r6 instruction varients.
* gas/mips/mips.exp: Add support for the mips32r6 and mips64r6
architectures. Also prevent non r6 supported tests from running.
Finally, add in support for running the new r6 tests.
(run_dump_test_arch): Add support for mipsr6 tests.
(run_list_test_arch): Add support for using files of the
form arch@testname.l .
include/elf/
* mips.h: Add relocs: R_MIPS_PC21_S2, R_MIPS_PC26_S2, R_MIPS_PC18_S3,
R_MIPS_PC19_S2, R_MIPS_PCHI16 and R_MIPS_PCLO16.
(E_MIPS_ARCH_32R6): New define.
(E_MIPS_ARCH_64R6): New define.
include/opcode/
* mips.h (mips_operand_type): Add new entries: OP_SAME_RS_RT,
OP_CHECK_PREV and OP_NON_ZERO_REG. Add descriptions for the MIPS R6
instruction arguments: -a, -b, -d, -s, -t, -u, -v, -w, -x, -y, -A, -B,
+I, +O, +R, +:, +\, +", +;
(mips_check_prev_operand): New struct.
(INSN2_FORBIDDEN_SLOT): New define.
(INSN_ISA32R6): New define.
(INSN_ISA64R6): New define.
(INSN_UPTO32R6): New define.
(INSN_UPTO64R6): New define.
(mips_isa_table): Add INSN_UPTO32R6 and INSN_UPTO64R6.
(ISA_MIPS32R6): New define.
(ISA_MIPS64R6): New define.
(CPU_MIPS32R6): New define.
(CPU_MIPS64R6): New define.
(cpu_is_member): Add cases for CPU_MIPS32R6, and CPU_MIPS64R6.
ld/
* ldmain.c (get_emulation): Add support for -mips32r6 and -mips64r6.
opcodes/
* mips-dis.c (mips_arch_choices): Add entries for mips32r6 and
mips64r6.
(parse_mips_dis_option): Allow MSA and virtualization support for
mips64r6.
(mips_print_arg_state): Add fields dest_regno and seen_dest.
(mips_seen_register): New function.
(print_insn_arg): Refactored code to use mips_seen_register
function. Add support for OP_SAME_RS_RT, OP_CHECK_PREV and
OP_NON_ZERO_REG. Changed OP_REPEAT_DEST_REG case to print out
the register rather than aborting.
(print_insn_args): Add length argument. Add code to correctly
calculate the instruction address for pc relative instructions.
(validate_insn_args): New static function.
(print_insn_mips): Prevent jalx disassembling for r6. Use
validate_insn_args.
(print_insn_micromips): Use validate_insn_args.
all the arguments are valid.
* mips-formats.h (PREV_CHECK): New define.
* mips-opc.c (decode_mips_operand): Add support for -a, -b, -d, -s,
-t, -u, -v, -w, -x, -y, -A, -B, +I, +O, +R, +:, +\, +", +;
(RD_pc): New define.
(FS): New define.
(I37): New define.
(I69): New define.
(mips_builtin_opcodes): Add MIPS R6 instructions. Exclude recoded
MIPS R6 instructions from MIPS R2 instructions.
This change moves the microMIPS 10-bit uninterpreted immediate code
embedded at bits 25..16 in the SYSCALL, WAIT, SDBBP and HYPCALL
instructions from `B' over to `+J' which is the operand code used in
the standard MIPS instruction set for a similar code embedded at bits
20..11, currently used by HYPCALL only in that set.
opcodes/
* micromips-opc.c (decode_micromips_operand): Rename `B' to `+J'.
(micromips_opcodes): Use "+J" in place of "B" for "hypcall",
"sdbbp", "syscall" and "wait".
include/opcode/
* mips.h: Document the move of `MICROMIPSOP_*_CODE10' from `B'
over to `+J'.
gas/
* config/tc-mips.c: Rename INSN_LOAD_COPROC_DELAY to INSN_LOAD_COPROC
and INSN_COPROC_MOVE_DELAY to INSN_COPROC_MOVE throughout.
include/opcode/
* mips.h (INSN_LOAD_COPROC_DELAY): Rename to...
(INSN_LOAD_COPROC): New define.
(INSN_COPROC_MOVE_DELAY): Rename to...
(INSN_COPROC_MOVE): New define.
opcodes/
* micromips-opc.c (COD): Rename throughout to...
(CM): New define, update to use INSN_COPROC_MOVE.
(LCD): Rename throughout to...
(LC): New define, update to use INSN_LOAD_COPROC.
* mips-opc.c: Likewise.
This patch firstly adds support for mips32r3 mips32r5, mips64r3
and mips64r5. Secondly it adds support for the eretnc instruction.
ChangeLog:
bfd/
* aoutx.h (NAME (aout, machine_type)): Add mips32r3, mips64r3,
mips32r5 and mips64r5.
* archures.c (bfd_architecture): Likewise.
* bfd-in2.h (bfd_architecture): Likewise.
* cpu-mips.c (arch_info_struct): Likewise.
* elfxx-mips.c (mips_set_isa_flags): Likewise.
gas/
* tc-mips.c (ISA_SUPPORTS_MIPS16E): Add mips32r3, mips32r5, mips64r3
and mips64r5.
(ISA_HAS_64BIT_FPRS): Likewise.
(ISA_HAS_ROR): Likewise.
(ISA_HAS_ODD_SINGLE_FPR): Likewise.
(ISA_HAS_MXHC1): Likewise.
(hilo_interlocks): Likewise.
(md_longopts): Likewise.
(ISA_HAS_64BIT_REGS): Add mips64r3 and mips64r5.
(ISA_HAS_DROR): Likewise.
(options): Add OPTION_MIPS32R3, OPTION_MIPS32R5, OPTION_MIPS64R3, and
OPTION_MIPS64R5.
(mips_isa_rev): Add support for mips32r3, mips32r5, mips64r3 and
mips64r5.
(md_parse_option): Likewise.
(s_mipsset): Likewise.
(mips_cpu_info_table): Add entries for mips32r3, mips32r5, mips64r3
and mips64r5. Also change p5600 entry to be mips32r5.
* configure.in: Add support for mips32r3, mips32r5, mips64r3 and
mips64r5.
* configure: Regenerate.
* doc/c-mips.texi: Document the -mips32r3, -mips32r5, -mips64r3 and
-mips64r5 command line options.
* doc/as.texinfo: Likewise.
gas/testsuite/
* gas/mips/mips.exp: Add MIPS32r5 tests. Also add the mips32r3,
mips32r5, mips64r3 and mips64r5 isas to the testsuite.
* gas/mips/r5.s: New test.
* gas/mips/r5.d: Likewise.
include/opcode/
* mips.h (INSN_ISA_MASK): Updated.
(INSN_ISA32R3): New define.
(INSN_ISA32R5): New define.
(INSN_ISA64R3): New define.
(INSN_ISA64R5): New define.
(INSN_ISA64, INSN_ISA64R2, INSN_ISA3_32, INSN_ISA3_32R2, INSN_ISA4_32
INSN_ISA4_32R2, INSN_ISA5_32R2): Renumbered.
(mips_isa_table): Add entries for mips32r3, mips32r5, mips64r3 and
mips64r5.
(INSN_UPTO32R3): New define.
(INSN_UPTO32R5): New define.
(INSN_UPTO64R3): New define.
(INSN_UPTO64R5): New define.
(ISA_MIPS32R3): New define.
(ISA_MIPS32R5): New define.
(ISA_MIPS64R3): New define.
(ISA_MIPS64R5): New define.
(CPU_MIPS32R3): New define.
(CPU_MIPS32R5): New define.
(CPU_MIPS64R3): New define.
(CPU_MIPS64R5): New define.
opcodes/
* mips-opc.c (mips_builtin_opcodes): Add MIPS32r5 eretnc instruction.
(I34): New define.
(I36): New define.
(I66): New define.
(I68): New define.
* mips-dis.c (mips_arch_choices): Add mips32r3, mips32r5, mips64r3 and
mips64r5.
(parse_mips_dis_option): Update MSA and virtualization support to
allow mips64r3 and mips64r5.
ChangeLog:
binutils/
* doc/binutils.texi: Document the disassemble MIPS XPA instructions
command line option.
gas/
* config/tc-mips.c (options): Add OPTION_XPA and OPTION_NO_XPA.
(md_longopts): Add xpa and no-xpa command line options.
(mips_ases): Add MIPS XPA ASE.
(mips_cpu_info_table): Update p5600 entry to allow the XPA ASE.
* doc/as.texinfo: Document the MIPS XPA command line options.
* doc/c-mips.texi: Document the MIPS XPA command line options,
and assembler directives.
gas/testsuite/
* gas/mips/mips.exp: Add xpa tests.
* gas/mips/xpa.s: New test.
* gas/mips/xpa.d: Likewise.
include/
* opcode/mips.h (ASE_XPA): New define.
opcodes/
* mips-dis.c (mips_arch_choices): Update mips32r2 and mips64r2
to allow the MIPS XPA ASE.
(parse_mips_dis_option): Process the -Mxpa option.
* mips-opc.c (XPA): New define.
(mips_builtin_opcodes): Add MIPS XPA instructions and move the
locations of the ctc0 and cfc0 instructions.
The element index range for the following MIPS MSA instructions: sldi, splati,
copy_s, copy_u, insert and insve is 1 bit too large. This patch fixes this issue.
ChangeLog:
gas/testsuite/gas/mips/
* msa.s: Reduced maximum element index range for sldi, splati,
copy_s, copy_u, insert and insve instructions.
* msa64.s: Likewise.
* micromips@msa.d: Likewise.
* micromips@msa64.d: Likewise.
* msa.d: Likewise.
* msa64.d: Likewise.
include/opcode/
* mips.h: Updated description of +o, +u, +v and +w for MIPS and
microMIPS.
opcodes/
* micromips-opc.c (decode_micromips_operand): Reduced range of +o, +u,
+v and +w.
(micromips_opcodes): Reduced element index range for sldi, splati,
copy_s, copy_u, insert and insve instructions.
* opcodes/mips-opc.c (decode_mips_operand): Reduced range of +o, +u,
+v and +w.
(mips_builtin_opcodes): Reduced element index range for sldi, splati,
copy_s, copy_u, insert and insve instructions.
* mips.h (M_DEXT, M_DINS): Delete.
opcodes/
* micromips-opc.c (micromips_opcodes): Replace "dext" and "dins"
macro entries with "dextm", "dextu", "dinsm" and "dinsu" aliases.
Use +H rather than +C for the real "dext".
* mips-opc.c (mips_builtin_opcodes): Likewise.
gas/
* config/tc-mips.c (report_bad_range, report_bad_field): Delete.
(macro): Remove M_DEXT and M_DINS handling.
gas/testsuite/
* gas/mips/ext-ill.l, gas/mips/mips64r2-ill.l: Expect DEXT and DINS
error messages to have the same form as the EXT and INS ones.
* gas/mips/micromips-insn32.d, gas/mips/micromips-noinsn32.d,
gas/mips/micromips-trap.d, gas/mips/micromips.d,
gas/mips/micromips@mips64r2.d, gas/mips/mips64r2.d: Expect
"dext" and "dins" instead of "dextm", "dextu", "dinsm" and "dinsu".
2013-08-04 Jürgen Urban <JuergenUrban@gmx.de>
Richard Sandiford <rdsandiford@googlemail.com>
* mips.h: Document new VU0 operand characters.
(OP_VU0_SUFFIX, OP_VU0_MATCH_SUFFIX): New mips_operand_types.
(OP_REG_VF, OP_REG_VI, OP_REG_R5900_I, OP_REG_R5900_Q, OP_REG_R5900_R)
(OP_REG_R5900_ACC): New mips_reg_operand_types.
(INSN2_VU0_CHANNEL_SUFFIX): New macro.
(mips_vu0_channel_mask): Declare.
opcodes/
2013-08-04 Jürgen Urban <JuergenUrban@gmx.de>
Richard Sandiford <rdsandiford@googlemail.com>
* mips-dis.c (print_reg): Handle OP_REG_VI, OP_REG_VF, OP_REG_R5900_I,
OP_REG_R5900_Q, OP_REG_R5900_R and OP_REG_R5900_ACC.
(print_vu0_channel): New function.
(print_insn_arg): Handle OP_VU0_SUFFIX and OP_VU0_MATCH_SUFFIX.
(print_insn_args): Handle '#'.
(print_insn_mips): Handle INSN2_VU0_CHANNEL_SUFFIX.
* mips-opc.c (mips_vu0_channel_mask): New constant.
(decode_mips_operand): Handle new VU0 operand types.
(VU0, VU0CH): New macros.
(mips_builtin_opcodes): Add VU0 opcodes. Use "+7" rather than "E"
for LQC2 and SQC2. Use "+9" rather than "G" for EE CFC2 and CTC2.
Use "+6" rather than "G" for QMFC2 and QMTC2.
gas/
2013-08-04 Jürgen Urban <JuergenUrban@gmx.de>
Richard Sandiford <rdsandiford@googlemail.com>
* config/tc-mips.c (MAX_OPERANDS): Bump to 6.
(RWARN): Bump to 0x8000000.
(RTYPE_VI, RTYPE_VF, RTYPE_R5900_I, RTYPE_R5900_Q, RTYPE_R5900_R)
(RTYPE_R5900_ACC): New register types.
(RTYPE_MASK): Include them.
(R5900_I_NAMES, R5900_Q_NAMES, R5900_R_NAMES, R5900_ACC_NAMES): New
macros.
(reg_names): Include them.
(mips_parse_register_1): New function, split out from...
(mips_parse_register): ...here. Add a channels_ptr parameter.
Look for VU0 channel suffixes when nonnull.
(reg_lookup): Update the call to mips_parse_register.
(mips_parse_vu0_channels): New function.
(OT_CHANNELS, OT_DOUBLE_CHAR): New mips_operand_token_types.
(mips_operand_token): Add a "channels" field to the union.
Extend the comment above "ch" to OT_DOUBLE_CHAR.
(mips_parse_base_start): Match -- and ++. Handle channel suffixes.
(mips_parse_argument_token): Handle channel suffixes here too.
(validate_mips_insn): Handle INSN2_VU0_CHANNEL_SUFFIX.
Ignore OP_VU0_MATCH_SUFFIX when calculating the used bits.
Handle '#' formats.
(md_begin): Register $vfN and $vfI registers.
(operand_reg_mask): Handle OP_VU0_SUFFIX and OP_VU0_MATCH_SUFFIX.
(convert_reg_type): Handle OP_REG_VI, OP_REG_VF, OP_REG_R5900_I,
OP_REG_R5900_Q, OP_REG_R5900_R and OP_REG_R5900_ACC.
(match_vu0_suffix_operand): New function.
(match_operand): Handle OP_VU0_SUFFIX and OP_VU0_MATCH_SUFFIX.
(macro): Use "+7" rather than "E" for LDQ2 and STQ2.
(mips_lookup_insn): New function.
(mips_ip): Use it. Allow "+K" operands to be elided at the end
of an instruction. Handle '#' sequences.
gas/testsuite/
2013-08-04 Jürgen Urban <JuergenUrban@gmx.de>
* gas/mips/r5900-vu0.d: Expect $vfN and $viN instead of numeric
coprocessor registers.
* gas/mips/r5900-all-vu0.s, gas/mips/r5900-all-vu0.d,
gas/mips/r5900-full-vu0.s, gas/mips/r5900-full-vu0.d,
gas/mips/r5900-error-vu0.s, gas/mips/r5900-error-vu0.l: New tests.
* gas/mips/mips.exp: Run them.
* mips.h (mips_pcrel_operand): Inherit from mips_int_operand.
(mips_int_operand_min, mips_int_operand_max): New functions.
(mips_decode_pcrel_operand): Use mips_decode_int_operand.
opcodes/
* mips-formats.h (PCREL): Reorder parameters and update the definition
to match new mips_pcrel_operand layout.
(JUMP, JALX, BRANCH): Update accordingly.
* mips16-opc.c (decode_mips16_operand): Likewise.
gas/
* config/tc-mips.c (match_int_operand): Use mips_int_operand_min
and mips_int_operand_max.
(mips16_immed_operand, mips16_immed_operands, MIPS16_NUM_IMMED):
Delete.
(mips16_immed_operand, mips16_immed_in_range_p): New functions.
(mips16_immed, mips16_extended_frag): Use them. Use mips_int_operand
instead of mips16_immed_operand.
* mips.h (MIPS16_INSN_WRITE_SP, MIPS16_INSN_READ_31)
(MIPS16_INSN_READ_PC, MIPS16_INSN_UNCOND_BRANCH)
(MIPS16_INSN_COND_BRANCH): Delete.
opcodes/
* mips16-opc.c (UBR, CBR, RD_31, RD_PC): Redefine as INSN2_* flags.
(WR_SP): Replace with...
(MOD_SP): ...this.
(mips16_opcodes): Update accordingly.
* mips-dis.c (print_insn_mips16): Likewise.
gas/
* config/tc-mips.c (compact_branch_p, uncond_branch_p): Use the same
flags for MIPS16 and non-MIPS16 instructions.
(gpr_mod_mask): Move the INSN2_MOD_SP case outside the micromips block.
(gpr_read_mask): Use INSN2_READ_GPR_31 for MIPS16 instructions too.
(gpr_write_mask): Remove MIPS16_INSN_WRITE_SP handling.
(can_swap_branch_p, get_append_method): Use the same flags for MIPS16
and non-MIPS16 instructions. Fix formatting.
* mips.h (mips_operand_type, mips_reg_operand_type): New enums.
(mips_operand, mips_int_operand, mips_mapped_int_operand)
(mips_msb_operand, mips_reg_operand, mips_reg_pair_operand)
(mips_pcrel_operand): New structures.
(mips_insert_operand, mips_extract_operand, mips_signed_operand)
(mips_decode_int_operand, mips_decode_pcrel_operand): New functions.
(decode_mips_operand, decode_micromips_operand): Declare.
opcodes/
* mips-formats.h: New file.
* mips-opc.c: Include mips-formats.h.
(reg_0_map): New static array.
(decode_mips_operand): New function.
* micromips-opc.c: Remove <stdio.h> include. Include mips-formats.h.
(reg_0_map, reg_28_map, reg_29_map, reg_31_map, reg_m16_map)
(reg_mn_map, reg_q_map, reg_h_map1, reg_h_map2, int_b_map)
(int_c_map): New static arrays.
(decode_micromips_operand): New function.
* mips-dis.c (micromips_to_32_reg_b_map, micromips_to_32_reg_c_map)
(micromips_to_32_reg_d_map, micromips_to_32_reg_e_map)
(micromips_to_32_reg_f_map, micromips_to_32_reg_g_map)
(micromips_to_32_reg_h_map1, micromips_to_32_reg_h_map2)
(micromips_to_32_reg_l_map, micromips_to_32_reg_m_map)
(micromips_to_32_reg_n_map, micromips_to_32_reg_q_map)
(micromips_imm_b_map, micromips_imm_c_map): Delete.
(print_reg): New function.
(mips_print_arg_state): New structure.
(init_print_arg_state, print_insn_arg): New functions.
(print_insn_args): Change interface and use mips_operand structures.
Delete GET_OP_S. Move GET_OP definition to...
(print_insn_mips): ...here. Update the call to print_insn_args.
(print_insn_micromips): Use print_insn_args.
gas/
* config/tc-mips.c (validate_mips_insn): Move further up file.
Add insn_bits and decode_operand arguments. Use the mips_operand
fields to work out which bits an operand occupies. Detect double
definitions.
(validate_micromips_insn): Move further up file. Call into
validate_mips_insn.
* mips.h (M_ACLR_OB, M_ASET_OB, M_CACHE_OB, M_CACHEE_OB, M_L_DOB)
(M_LB_A, M_LBE_OB, M_LBU_A, M_LBUE_OB, M_LD_A, M_LD_OB, M_LDC2_OB)
(M_LDL_OB, M_LDM_OB, M_LDP_OB, M_LDR_OB, M_LH_A, M_LHE_OB, M_LHU_A)
(M_LHUE_OB, M_LL_OB, M_LLD_OB, M_LLE_OB, M_LS_A, M_LW_A, M_LWE_OB)
(M_LWC0_A, M_LWC1_A, M_LWC2_A, M_LWC2_OB, M_LWC3_A, M_LWL_A, M_LWL_OB)
(M_LWLE_OB, M_LWM_OB, M_LWP_OB, M_LWR_A, M_LWR_OB, M_LWRE_OB, M_LWU_OB)
(M_PREF_OB, M_PREFE_OB, M_S_DOB, M_SAA_OB, M_SAAD_OB, M_SC_OB)
(M_SCD_OB, M_SCE_OB, M_SD_A, M_SD_OB, M_SDC2_OB, M_SDL_OB, M_SDM_OB)
(M_SDP_OB, M_SDR_OB, M_SB_A, M_SBE_OB, M_SH_A, M_SHE_OB, M_SW_A)
(M_SWE_OB, M_SWC0_A, M_SWC1_A, M_SWC2_A, M_SWC2_OB, M_SWC3_A, M_SWL_A)
(M_SWL_OB, M_SWLE_OB, M_SWM_OB, M_SWP_OB, M_SWR_A, M_SWR_OB, M_SWRE_OB)
(M_ULD, M_ULH, M_ULHU, M_ULW, M_USH, M_USW, M_USD): Delete.
(M_ULD_A, M_ULH_A, M_ULHU_A, M_ULW_A, M_USH_A, M_USW_A, M_USD_A):
Rename to...
(M_ULD_AB, M_ULH_AB, M_ULHU_AB, M_ULW_AB, M_USH_AB, M_USW_AB)
(M_USD_AB): ...these.
opcodes/
* mips-opc.c (mips_builtin_opcodes): Remove o(b) macros. Move LD
and SD A(B) macros up.
* micromips-opc.c (micromips_opcodes): Likewise.
gas/
* config/tc-mips.c (gprel16_reloc_p): New function.
(macro_read_relocs): Assume BFD_RELOC_LO16 if all relocs are
BFD_RELOC_UNUSED.
(offset_high_part, small_offset_p): New functions.
(nacro): Use them. Remove *_OB and *_DOB cases. For single-
register load and store macros, handle the 16-bit offset case first.
If a 16-bit offset is not suitable for the instruction we're
generating, load it into the temporary register using
ADDRESS_ADDI_INSN. Make the M_LI_DD code fall through into the
M_L_DAB code once the address has been constructed. For double load
and store macros, again handle the 16-bit offset case first.
If the second register cannot be accessed from the same high
part as the first, load it into AT using ADDRESS_ADDI_INSN.
Fix the handling of LD in cases where the first register is the
same as the base. Also handle the case where the offset is
not 16 bits and the second register cannot be accessed from the
same high part as the first. For unaligned loads and stores,
fuse the offbits == 12 and old "ab" handling. Apply this handling
whenever the second offset needs a different high part from the first.
Construct the offset using ADDRESS_ADDI_INSN where possible,
for offbits == 16 as well as offbits == 12. Use offset_reloc
when constructing the individual loads and stores.
(mips_ip): Set up imm_expr, imm2_expr, offset_expr, imm_reloc
and offset_reloc before matching against a particular opcode.
Handle elided 'A' constants. Allow 'A' constants to use
relocation operators.
gas/testsuite/
* gas/mips/ldstla-32.d: Avoid "lui at,0x0" sequences for
truncated constants.
* gas/mips/ldstla-32-shared.d: Likewise.
* gas/mips/mcu.d: Use ADDIU in preference to LI+ADDU when adding
16-bit constants to the base.
* gas/mips/micromips@mcu.d: Likewise.
* gas/mips/micromips@cache.d: Likewise.
* gas/mips/micromips@pref.d: Likewise.
* gas/mips/micromips.d, gas/mips/micromips-insn32.d,
gas/mips/micromips-noinsn32.d, gas/mips/micromips-trap.d: Likewise.
Allow the full 16-bit offset range to be used for SB, LB and LBU in
USH and ULH sequences. Fix the expected output for LD and SD when
the two LW and SW offsets need different high parts.
* gas/mips/eva.s: Test PREFE with relocation operators.
* gas/mips/eva.d: Use ADDIU in preference to LI+ADDU for 16-bit
constants. Update after eva.s change.
* gas/mips/micromips@eva.d: Likewise.
* gas/mips/ld-reloc.s, gas/mips/ld-reloc.d, gas/mips/l_d-reloc.s,
gas/mips/l_d-reloc.d, gas/mips/ulw-reloc.s, gas/mips/ulw-reloc.d,
gas/mips/micromips@ulw-reloc.d, gas/mips/ulh-reloc.s,
gas/mips/ulh-reloc.d: New tests.
* gas/mips/mips.exp: Run them.
* mips.h: Remove documentation of "[" and "]". Update documentation
of "k" and the MDMX formats.
opcodes/
* mips-opc.c (mips_builtin_opcodes): Use "Q" for the INSN_5400
MDMX-like instructions.
* mips-dis.c (print_insn_arg): Use "$f" rather than "$v" when
printing "Q" operands for INSN_5400 instructions.
gas/
* config/tc-mips.c (validate_mips_insn): Remove "[" and "]" handling.
(mips_ip): Likewise. Do not set is_mdmx for INSN_5400 instructions.
Check constraints on the VR5400 RZU.OB, SLL.OB and SRL.OB instructions.
gas/testsuite/
* gas/mips/vr5400-ill.s, gas/mips/vr5400-ill.l: New test.
* gas/mips/mips.exp: Run it.
* mips.h: Update documentation of "+s" and "+S".
opcodes/
* mips-opc.c (mips_builtin_opcodes): Use "+s" for "cins32" and
"+S" for "cins".
* mips-dis.c (print_mips_arg): Update "+s" and "+S" comments.
Combine cases.
gas/
* config/tc-mips.c (mips_ip): Preserve the real bit number for "+p".
Require the msb to be <= 31 for "+s". Check that the size is <= 31
for both "+s" and "+S".
* mips.h: Document "+i".
opcodes/
* mips-opc.c (mips_builtin_opcodes): Use "+i" rather than "a" for
"jalx".
* mips16-opc.c (mips16_opcodes): Likewise.
* micromips-opc.c (micromips_opcodes): Likewise.
* mips-dis.c (print_insn_args, print_mips16_insn_arg)
(print_insn_mips16): Handle "+i".
(print_insn_micromips): Likewise. Conditionally preserve the
ISA bit for "a" but not for "+i".
gas/
* config/tc-mips.c (validate_mips_insn, validate_micromips_insn):
(mips_ip, mips16_ip): Handle "+i".
* mips.h: Remove documentation of "+D" and "+T".
opcodes/
* mips-opc.c (mips_builtin_opcodes): Remove "+D" and "+T" entries.
* micromips-opc.c (micromips_opcodes): Likewise.
* mips-dis.c (print_insn_args, print_insn_micromips): Remove "+D"
and "+T" handling. Check for a "0" suffix when deciding whether to
use coprocessor 0 names. In that case, also check for ",H" selectors.
gas/
* config/tc-mips.c (validate_mips_insn, validate_micromips_insn)
(mips_ip): Remove "+D" and "+T" handling.
gas/testsuite/
* gas/mips/lb.d, gas/mips/sb.d: Use coprocessor register names
for LWC0 and SWC0.
* mips.h: Fix comment for "1": it is now STYPE rather than SHAMT.
Use "source" rather than "destination" for microMIPS "G".
gas/
* config/tc-mips.c (validate_mips_insn): Use STYPE rather than SHAMT.
2013-06-08 Catherine Moore <clm@codesourcery.com>
* config/tc-mips.c (is_opcode_valid): Build ASE mask.
(is_opcode_valid_16): Pass ase value to opcode_is_member.
(append_insn): Change INSN_xxxx to ASE_xxxx.
include/
2013-06-08 Catherine Moore <clm@codesourcery.com>
* opcode/mips.h (mips_opcode): Add ase field.
(INSN_ASE_MASK): Delete.
(INSN_DSP): Rename to ASE_DSP. Provide new value.
(INSN_DSPR2): Rename to ASE_DSPR2. Provide new value.
(INSN_MCU): Rename to ASE_MCU. Provide new value.
(INSN_MDMX): Rename to ASE_MDMX. Provide new value.
(INSN_MIPS3d): Rename to ASE_MIPS3D. Provide new value.
(INSN_MT): Rename to ASE_MT. Provide new value.
(INSN_SMARTMIPS): Rename to ASE_SMARTMIPS. Provide new value.
(INSN_VIRT): Rename to ASE_VIRT. Provide new value.
(INSN_VIRT64): Rename to ASE_VIRT64. Provide new value.
(opcode_is_member): Add ase argument. Check ase.
opcodes/
2013-06-08 Catherine Moore <clm@codesourcery.com>
Richard Sandiford <rdsandiford@googlemail.com>
* micromips-opc.c (D32, D33, MC): Update definitions.
(micromips_opcodes): Initialize ase field.
* mips-dis.c (mips_arch_choice): Add ase field.
(mips_arch_choices): Initialize ase field.
(set_default_mips_dis_options): Declare and setup mips_ase.
* mips-opc.c (M3D, SMT, MX, IVIRT, IVIRT64, D32, D33, D64,
MT32, MC): Update definitions.
(mips_builtin_opcodes): Initialize ase field.
* doc/binutils.texi: Document -Mvirt disassembler option.
gas/ChangeLog:
* config/tc-mips.c (struct mips_set_options): New ase_virt field.
(mips_opts): Update for the new field.
(file_ase_virt): New variable.
(ISA_SUPPORTS_VIRT_ASE): New macro.
(ISA_SUPPORTS_VIRT64_ASE): New macro.
(MIPS_CPU_ASE_VIRT): New define.
(is_opcode_valid): Handle ase_virt.
(macro_build): Handle "+J".
(validate_mips_insn): Likewise.
(mips_ip): Likewise.
(enum options): Add OPTION_VIRT and OPTION_NO_VIRT.
(md_longopts): Add mvirt and mnovirt
(md_parse_option): Handle OPTION_VIRT and OPTION_NO_VIRT.
(mips_after_parse_args): Handle ase_virt field.
(s_mipsset): Handle "virt" and "novirt".
(mips_elf_final_processing): Add a comment about virt ASE might need a new flag.
(md_show_usage): Print out the usage of -mvirt and mno-virt options.
* doc/c-mips.texi: Document -mvirt and -mno-virt.
Document ".set virt" and ".set novirt".
gas/testsuite/ChangeLog:
* gas/mips/mips.exp: Run virt and virt64 testcases.
* gas/mips/virt.d: New file.
* gas/mips/virt.s: New file.
* gas/mips/virt64.d: New file.
* gas/mips/virt64.s: New file.
include/opcode/ChangeLog:
* mips.h (OP_MASK_CODE10): Correct definition.
(OP_SH_CODE10): Likewise.
Add a comment that "+J" is used now for OP_*CODE10.
(INSN_ASE_MASK): Update.
(INSN_VIRT): New macro.
(INSN_VIRT64): New macro
opcodes/ChangeLog:
* mips-dis.c (mips_arch_choices): Add INSN_VIRT to mips32r2 .
Add INSN_VIRT and INSN_VIRT64 to mips64r2.
(parse_mips_dis_option): Handle the virt option.
(print_insn_args): Handle "+J".
(print_mips_disassembler_options): Print out message about virt64.
* mips-opc.c (IVIRT): New define.
(IVIRT64): New define.
(mips_builtin_opcodes): Add dmfgc0, dmtgc0, hypcall, mfgc0, mtgc0,
tlbgr, tlbgwi, tlbginv, tlbginvf, tlbgwr, tlbgp VIRT instructions.
Move rfe to the bottom as it conflicts with tlbgp.
* bfd-in2.h: Add support for MIPS r5900
* config.bfd: Add support for Sony Playstation 2
* cpu-mips.c: Add support for MIPS r5900
* elfxx-mips.c: Add support for MIPS r5900 (extension of r4000)
* config/tc-mips.c: Add support for MIPS r5900
Add M_LQ_AB and M_SQ_AB to support large values for instructions lq and sq.
* config/tc-mips.c (can_swap_branch_p, get_append_method): Detect some conditional short loops to fix a bug on the r5900 by NOP in the branch delay slot.
* config/tc-mips.c (M_MUL): Support 3 operands in multu on r5900.
* config/tc-mips.c (M_TRUNCWS): Support trunc.w.s on r5900 in MIPS ISA I.
* config/tc-mips.c (s_mipsset): Force 32 bit floating point on r5900.
* configure.in: Detect CPU type when target string contains r5900 (e.g. mips64r5900el-linux-gnu).
* config/tc-mips.c (mips_ip): Check parameter range of instructions mfps and mtps on r5900.
* elf/mips.h: Add MIPS machine variant number for r5900 which is compatible with old Playstation 2 software.
* opcode/mips.h: Add support for r5900 instructions including lq and sq.
* configure.tgt: Support ELF files for Sony Playstation 2 (for ps2dev and ps2sdk).
* emulparams/elf32lr5900n32.sh: Create linker script for Sony Playstation 2 ELF files using MIPS ABI n32.
* emulparams/elf32lr5900.sh: Create linker script for Sony Playstation 2 ELF files using MIPS ABI o32.
* Makefile.am: Add linker scripts for Sony Playstation 2 ELF files.
* opcodes/mips-dis.c: Add names for CP0 registers of r5900.
* opcodes/mips-opc.c: Add M_SQ_AB and M_LQ_AB to support larger range for instructions sq and lq.
* opcodes/mips-opc.c: Add support for MIPS r5900 CPU.
Add support for 128 bit MMI (Multimedia Instructions).
Add support for EE instructions (Emotion Engine).
Disable unsupported floating point instructions (64 bit and undefined compare operations).
Enable instructions of MIPS ISA IV which are supported by r5900.
Disable 64 bit co processor instructions.
Disable 64 bit multiplication and division instructions.
Disable instructions for co-processor 2 and 3, because these are not supported (preparation for later VU0 support (Vector Unit)).
Disable cvt.w.s because this behaves like trunc.w.s and the correct execution can't be ensured on r5900.
Add trunc.w.s using the opcode encoding of cvt.w.s on r5900. This will confuse less developers and compilers.
