a location whose address has to be resolved via the minimal
symbol table.
* buildsym.c (finish_block), findvar.c (symbol_read_needs_frame,
read_var_value), printcmd.c (address_info),
symmisc.c (print_symbol, print_partial_symbol): Handle
LOC_UNRESOLVED.
* stabsread.c (scan_file_globals): Change unresolved LOC_STATIC
symbols to LOC_UNRESOLVED. Remove rt_common_objfile lookup
kludge, global common symbols are now handled by LOC_UNRESOLVED.
(scan_file_globals_1): Move code back to scan_file_globals,
delete.
around calls to create_longjmp_breakpoint. Why install the
breakpoints if we can't find the longjmp target?
* infrun.c (wait_for_inferior): Cleanup comments near call test.
* remote-mips.c: Fixed a bunch of prototypes to avoid char/int
complaint from picky compilers. Add comment to mips_expect.
Replace all instances of sr_get_debug with remote_debug.
* (mips_readchar): Don't jam init string to monitor.
mips_initialize() handles that.
* (mips_receive_header): Print better message when we get too
much garbage.
* (mips_request): Allow caller to pass in buff to allow them to
analyze the returned message.
* (mips_initialize): Re-do initialization to try sending a BREAK,
a ^C, and then a download escape sequence. Cleanup protocol
startup. Eliminate sleeps. Clear breakpoints (if using monitor
breakpoints). Re-init frame.
* (mips_detach): Close down target.
start-sanitize-gm
* (mips_resume): Pass signal down to target.
* (mips_create_inferior): Start target with TARGET_SIGNAL_PWR.
end-sanitize-gm
* (mips_wait): Handle return status with registers, or breakpoint stuff.
* (mips_kill): Add ^C handling.
* (mips_insert_breakpoint mips_remove_breakpoint): Call new
breakpoint stuff if enabled.
* (calculate_mask remote_mips_set_watchpoint
remote_mips_remove_watchpoint remote_mips_stopped_by_watchpoint):
Hardware watchpoint/breakpoint stuff.
* (common_breakpoint): Common code for new monitor breakpoint commands.
* (mips_load): Don't use `prompt'. It's a global variable.
* top.c (dont_repeat_command): New command for use in
user-defined commands to suppress auto-repeat (by hittin return key).
start-sanitize-gm
* utils.c (request_quit): Call target_kill here. Good idea.
Needs a better implementation.
end-sanitize-gm
* valops.c: Add start of auto function-call abandonment capability.
start-sanitize-gm
* c-exp.y: Add code (currently disabled) to handle GM dynamic
structures (it conflicts with @!).
* eval.c (evaluate_subexp_standard): ditto.
* expprint.c (print_subexp dump_expression): ditto.
* expression.h (enum exp_opcode): ditto.
* parse.c (length_of_subexp): ditto.
* configure, configure.in: Add mip*-*-magic* target.
* magic.c magic.h: Special routines to handle GM stuff (like
stepping through dispatcher).
end-sanitize-gm
of native support.
* mpw-make.sed: Disable subdir recursion, edit out useless rule.
* mac-xdep.c (Values.h): Don't include.
(GestaltEqu.h): Include Gestalt.h instead.
(do_mouse_down): Comment out control tracking, needs to be
updated to use UPP before will work on PowerMac.
* regex.c: Renamed to gnu-regex.c.
* Makefile.in (POSSLIBS): Refer to gnu-regex.h and gnu-regex.c.
(REGEX, REGEX1): Change to gnu-regex.o instead of regex.o.
(regex.o): Renamed to gnu-regex.o; refer to gnu-regex.c.
(irix5-nat.o, osfsolib.o, gnu-regex.o, solib.o, source.o, symtab.o):
Likewise.
* irix5-nat.c, osfsolib.c, gnu-regex.c, solib.c, source.c, symtab.c):
Include "gnu-regex.h" instead of "regex.h".
* alpha-tdep.c (in_prologue): Rename to alpha_in_prologue, to
avoid conflicts with symtab.h.
fixes building gdb under OSF/1 4.0
* config/pa/hppahpux.mh: Remove hardcoding of X locations.
* Makefile.in: Use X11_CFLAGS, X11_LDFLAGS and X11_LIBS.
* configure.in: Link X statically on Solaris, SunOS and HPUX.
with the obvious extension. (monitor_read_memory_single): Use
regexp for getmem.resp_delim because of parsing ambiguities caused
by certain monitors. (monitor_read_memory): Use new regexp stuff
to parse getmem.resp_delim.
* sh3-rom.c: Finish off table. Use new regexp capability for
getmem commands.
the step range test. Replace call detection test with much
simpler (and more efficient) test that doesn't require prologue
examination (as often).
* symtab.c symtab.h (in_prologue): New function that indicates
whether or not we are in a function prologue. This uses the
symbol table, and then falls back to prologue examination if that
fails. It's much more efficient for remote debugging because it
avoids examining memory, which is very slow. This is used in
wait_for_inferior to determine if we've made a function call that
needs to be skipped over (for next/nexti).
* mips-tdep.c (after_prologue): New function, returns the PC
after the prologue. Uses PDRs and the symbol table.
(mips_find_saved_regs): Use in_prologue() to avoid costly
prologue examination if possible.
(mips_skip_prologue): Use after_prologue() if possible to avoid
costly prologue examination.
Do not set saved registers from heuristics for a sigtramp frame.
* dwarfread.c (enum_type): Determine signedness of enum type
from enumerators.
* mips-tdep.c: Include gdb_string.h, gcc -Wall lint.
* rs6000-nat.c (xcoff_relocate_core): Fix typo.
* valops.c (value_repeat): Fix length of memory transfer to
match recent allocate_repeat_value change.
build config.h, add empty definitions to mk.tmp.
(powerpc-apple-macos): Make it work.
* mpw-make.sed: New file, sed commands to translate Unix makefile
into MPW syntax.
* mpw-make.in: Remove.
* mac-gdb.r: New file, was macgdb.r, renamed for consistency
with other tools, now includes cfrg resource.
* macgdb.r: Remove.
* config/m68k/xm-mpw.h: Remove most of contents, replace with
include of include/mpw/mpw.h.
_initialize_array to array_open. It was forcing the baud rate of
all targets to be 4800 baud! Seems like I've fixed this before...
* config/mips/idt.mt (TDEPFILES): Remove remote-array.o. This
has *nothing* to do with IDT!!!
sh3 monitor support.
* monitor.c: Cleanup regexp compilation stuff to make it easier
to use several regexps.
* monitor.h: Get rid of struct rom_cmd_data. It's no longer used.
* config/m68k/tm-monitor.h: Don't redefine NUM_REGS here. It just
causes GDB to crash.
screws up too many targets.
* sparcl-stub.c: Add prototypes to many forward decls.
* Create private copies of strlen, strcpy, and memcpy to prevent
chaos when user steps into them.
* (trap_low handle_exception): Clean up DSU support code
(hardware breakpoints). Move lots of stuff from asm-land to
C-land (make it much easier to #ifdef if necessary). Also, use
trap 255 to get into break mode instead of doing a DSU register
write, which may trash the register.
* (putpacket): Don't check return value of putDebugChar. It
returns void...
mentioned in the dld_list can't be found.
Warning seems more reasonable than croaking.
* config/pa/tm-hppah.h (FRAME_SAVED_PC_IN_SIGTRAMP): Dig out
the PC from the PC queues rather than %r31.
Fixes net bug. Might also fix one of the hpux10 corefile.exp failures,
not sure (will test when I get back monday morning).
