that hardware watchpoint removal problems won't leave breakpoint
traps in the target.
* configure configure.in: Make --enable-gdbtk be the default.
* remote-e7000.c (e7000_insert_breakpoint,
e7000_remove_breakpoint): Use e7000 based breakpoints, not memory
breakpoints.
* (e7000_wait): Adjust PC back by two when we see a breakpoint to
compensate for e7000 maladjustment.
* sparcl-tdep.c (sparclite_check_watch_resources): Fix logic bug
which prevented hardware watchpoints from working.
around calls to create_longjmp_breakpoint. Why install the
breakpoints if we can't find the longjmp target?
* infrun.c (wait_for_inferior): Cleanup comments near call test.
* remote-mips.c: Fixed a bunch of prototypes to avoid char/int
complaint from picky compilers. Add comment to mips_expect.
Replace all instances of sr_get_debug with remote_debug.
* (mips_readchar): Don't jam init string to monitor.
mips_initialize() handles that.
* (mips_receive_header): Print better message when we get too
much garbage.
* (mips_request): Allow caller to pass in buff to allow them to
analyze the returned message.
* (mips_initialize): Re-do initialization to try sending a BREAK,
a ^C, and then a download escape sequence. Cleanup protocol
startup. Eliminate sleeps. Clear breakpoints (if using monitor
breakpoints). Re-init frame.
* (mips_detach): Close down target.
start-sanitize-gm
* (mips_resume): Pass signal down to target.
* (mips_create_inferior): Start target with TARGET_SIGNAL_PWR.
end-sanitize-gm
* (mips_wait): Handle return status with registers, or breakpoint stuff.
* (mips_kill): Add ^C handling.
* (mips_insert_breakpoint mips_remove_breakpoint): Call new
breakpoint stuff if enabled.
* (calculate_mask remote_mips_set_watchpoint
remote_mips_remove_watchpoint remote_mips_stopped_by_watchpoint):
Hardware watchpoint/breakpoint stuff.
* (common_breakpoint): Common code for new monitor breakpoint commands.
* (mips_load): Don't use `prompt'. It's a global variable.
* top.c (dont_repeat_command): New command for use in
user-defined commands to suppress auto-repeat (by hittin return key).
start-sanitize-gm
* utils.c (request_quit): Call target_kill here. Good idea.
Needs a better implementation.
end-sanitize-gm
* valops.c: Add start of auto function-call abandonment capability.
start-sanitize-gm
* c-exp.y: Add code (currently disabled) to handle GM dynamic
structures (it conflicts with @!).
* eval.c (evaluate_subexp_standard): ditto.
* expprint.c (print_subexp dump_expression): ditto.
* expression.h (enum exp_opcode): ditto.
* parse.c (length_of_subexp): ditto.
* configure, configure.in: Add mip*-*-magic* target.
* magic.c magic.h: Special routines to handle GM stuff (like
stepping through dispatcher).
end-sanitize-gm
commands.
* top.c (struct user_args): Structure for holding arguments to
user defined commands.
(print_command_line): Delete unused "tmp_chain" variable. Clean
up flow control by having cases exit in the same manner.
Before executing a command or evaluating an expression, substitute
the current $arg0..$arg9 values if the command/expression uses them.
(arg_cleanup): New function.
(setup_user_args, locate_arg, insert_args): Likewise.
(execute_user_command): Allow arguments to user defined commands.
* Allow if/while commands to be used within a breakpoint command
list.
* breakpoint.c (bpstat_do_actions): Call execute_control_command
rather than execute_command (passes entire command structure rather
than just the command line text).
(breakpoint_1): Use "print_command_line" to print a breakpoint
command line (including control structures).
* gdbcmd.h (execute_control_command): Provide extern decl.
(print_command_line): Likewise.
* top.c (execute_control_command): No longer static.
(print_command_line): New function to recursively print a command
line, including control structures.
and stack pointer during stepping, to speed things up.
A. Changes to not select a frame until we need a selected frame:
* blockframe.c (flush_cached_frames): Call select_frame (NULL, -1).
* infrun.c (wait_for_inferior): Move call to select_frame back to
normal_stop. This reverts a change of 13 Apr 94 (it says Jeff
Law, but the change was my idea); the only reason for that change
was so we could save and restore the selected frame in
wait_for_inferior, and now that flush_cached frames clears the
selected frame, that should work OK now.
B. Changes to not create a current_frame until we need one:
* blockframe.c (get_current_frame): If current_frame is NULL, try
to create an innermost frame.
* sparc-tdep.c (sparc_pop_frame), infcmd.c (run-stack_dummy),
infrun.c (wait_for_inferior), thread.c (thread_switch),
convex-tdep.c (set_thread_command), a29k-tdep.c (pop_frame),
alpha-tdep.c (alpha_pop_frame), convex-xdep.c (core_file_command),
h8300-tdep.c (h8300_pop_frame), h8500-tdep.c (h8300_pop_frame),
hppa-tdep.c (hppa_pop_frame), i386-tdep.c (i386_pop_frame),
i960-tdep.c (pop_frame), m68k-tdep.c
(m68k_pop_frame), mips-tdep.c (mips_pop_frame), rs6000-tdep.c
(push_dummy_frame, pop_dummy_frame, pop_frame), sh-tdep.c
(pop_frame), config/arm/tm-arm.h (POP_FRAME),
config/convex/tm-convex.h (POP_FRAME), config/gould/tm-pn.h
(POP_FRAME), config/ns32k/tm-merlin.h (POP_FRAME),
config/ns32k/tm-umax.h (POP_FRAME), config/tahoe/tm-tahoe.h
(POP_FRAME), config/vax/tm-vax.h (POP_FRAME): Don't
call create_new_frame.
* corelow.c (core_open), altos-xdep.c (core_file_command),
arm-xdep.c (core_file_command), gould-xdep.c (core_file_command),
m3-nat.c (select_thread), sun386-nat.c (core_file_command),
umax-xdep.c (core_file_command): Don't call create_new_frame; do
call flush_cached_frames.
* blockframe.c (reinit_frame_cache): Don't call create_new_frame
or select_frame.
C. Changes to get rid of stop_frame_address and instead only
fetch the frame pointer when we need it.
* breakpoint.c (bpstat_stop_status): Remove argument
frame_address; use FRAME_FP (get_current_frame ()).
* infrun.c (wait_for_inferior): Don't pass frame pointer to
bpstat_stop_status.
* infrun.c (wait_for_inferior): Use FRAME_FP (get_current_frame
()) instead of stop_frame_address.
* infrun.c (save_inferior_status, restore_inferior_status),
inferior.h (struct inferior_status): Don't save and restore
stop_frame_address.
* inferior.h, infcmd.c, thread.c (thread_switch), m3-nat.c
(select_thread): Remove stop_frame_address and uses thereof.
D. Same thing for the stack pointer.
* infrun.c (wait_for_inferior): Remove stop_sp and replace
uses thereof with read_sp ().
E. Change to eliminate one nasty little spot where we were
wanting to know the frame pointer from before the current step
(idea from GDB 3.5, which saved my ass, because my other ideas of
how to fix it were very baroque).
* infrun.c: Remove prev_frame_address.
* infrun.c (wait_for_inferior, step_over_function): Use
step_frame_address instead of prev_frame_address.
F. Same basic idea for the stack pointer.
* inferior.h, infcmd.c: New variable step_sp.
* infcmd.c (step_1, until_next_command): Set it.
* infrun.c: Remove prev_sp and replace uses by step_sp.
* infrun.c (wait_for_inferior): If we get out of the step
range, then set step_sp to the current stack pointer before we
start going again.
* breakpoint.c (delete_breakpoint, enable_breakpoint,
disable_breakpoint): Don't call breakpoints_changed; it is now
called via the *_breakpoint_hook functions.
* annotate.c (_initialize_annotate, breakpoint_changed): New functions.
--enable-xxx configure option by adding ENABLE_{CLIBS DEPFILES}
where appropriate.
* General hackery to support alternate user-interface.
* breakpoint.c (mention, delete_breakpoint, enable_breakpoint,
disable_breakpoint): Call hooks for alternate user-interface.
* defs.h: Add declarations for alternate user-interface hooks.
* main.c (main): Add --nw (and --nowindows) options to disable
the GUI.
* (near call to command_loop): Call command_loop_hook if set.
* (fputs_unfiltered): Call fputs_unfiltered_hook if set.
* stack.c: Call print_frame_info_listing_hook if set.
* top.c (gdb_init): Initialize targets.c and utils.c prior to
other files to make sure that calls to error and warning will
work. Call init_ui_hook after everything else.
* utils.c (query): Call query_hook if set.
* (gdb_flush): Call flush_hook if set.
* Change _initialize_utils to initialize_utils cuz we don't use
automatic initialization of utils.c anymore.
* Support for TK GUI.
* Makefile.in: Add rule for gdbtk.o.
* configure.in: Add support for --enable-gdbtk.
* gdbtk.c: New file. Contains support routines for TK interface.
* gdbtk.tcl: New file. Implements GUI policy.
* remote.c: Get rid of #ifdef DONT_USE_REMOTE. It's no longer
necessary.
* breakpoint.h (hit_count): New breakpoint field.
* breakpoint.c (show_breakpoint_hit_counts): New variable.
(clear_breakpoint_hit_counts): New function.
(bpstat_stop_status): Increment the hit count.
(breakpoint_1): Display the hit count.
* infcmd.c (run_command): Reset breakpoint hit counts.
* target.c (generic_mourn_inferior): Don't clear ignore counts if
displaying hit counts.
target null pointer.
* blockframe.c (find_frame_addr_in_frame_chain): Likewise.
* printcmd.c (output_command): Annotate things we print here too.
* Move declaration of print_value_flags from defs.h to value.h.
* main.c (command_line_input): Call wrap_here as well as gdb_flush.
the same as --annotate=1.
(command_line_input): Print annotatation before and after prompt.
* blockframe.c (flush_cached_frames): Print annotation.
* Rename frame_file_full_name to annotation_level and move it from
symtab.h to defs.h.
* source.c (identify_source_line): If annotation_level > 1,
change output format.
* breakpoint.c: Print annotation whenever a breakpoint changes.
* main.c: New variable server_command.
(command_line_input): Parse "server " and set server_command.
(dont_repeat): Check server_command.
bp_watchpoint_scope breakpoints.
(struct breakpoint): Add val_chain and related_breakpoint fields
for use by watchpoints.
* breakpoint.c (within_scope): Delete. No longer used.
(TARGET_CAN_USE_HARDWARE_WATCHPOINT): Provide default definition.
(target_{remove,insert}_watchpoint): Likewise.
(can_use_hardware_watchpoint): New function.
(remove_breakpoint): New function to remove a single breakpoint
or hardware watchpoint.
(insert_breakpoints): Handle insertion of hardware watchpoints.
Store a copy of the value chain derived from the watchpoint
expression.
(remove_breakpoints): Simplify by using remove_breakpoint.
(delete_breakpoint): Likewise.
(watchpoint_check): Delete the watchpoint and watchpoint scope
breakpoints when the watchpoint goes out of scope. Save & restore
the current frame after checking watchpoints.
(breakpoint_init_inferior): Likewise (restarting the program
makes all local watchpoints go out of scope).
(bpstat_stop_status): Handle hardware watchpoints much like normal
watchpoints. Delete the watchpoint and watchpoint scope breakpoint
when the watchpoint goes out of scope. Remove and reinsert all
breakpoints before returning if we stopped when a hardware watchpoint
fired.
(watch_command): Use a hardware watchpoint when possible. If
watching a local expression, build a scope breakpoint too.
(map_breakpoint_numbers): Also call given function for any
related breakpoints.
(disable_breakpoint): Never disable a scope breakpoint.
(enable_breakpoint): Handle hardware breakpoints much like normal
breakpoints, but recompute the watchpoint_scope breakpoint's
frame and address (if we have an associated scope breakpoint).
(read_memory_nobpt): Handle hardware watchpoints like normal
watchpoints. When necessary handle watchpoint_scope breakpoints.
(print_it_normal, bpstat_what, breakpoint_1, mention): Likewise.
(clear_command, breakpoint_re_set_one, enable_command): Likewise.
(disable_command): Likewise.
* blockframe.c (find_frame_addr_in_frame_chain): New function.
Extern prototype added to frame.h
* infrun.c (wait_for_inferior): Set current_frame and select
a frame before checking if we stopped due to a hardare watchpoint
firing. Handle stepping over hardware watchpoints.
(normal_stop): Remove unnecessary call to select_frame.
* value.h (value_release_to_mark): Declare.
* values.c (value_release_to_mark): New function.
* procfs.c (procfs_wait): Add cases for hardware watchpoints.
(procfs_set_watchpoint, procfs_stopped_by_watchpoint): New functions.
* hppab-nat.c (hppa_set_watchpoint): New function.
* config/pa/nm-hppab.h (STOPPED_BY_WATCHPOINT): Define.
(HAVE_STEPPABLE_WATCHPOINT): Define.
(TARGET_CAN_USE_HARDWARE_WATCHPOINT): Define.
(target_{insert,delete}_watchpoint): Define.
cp-valprint.c, eval.c, expprint.c, findvar.c, language.c,
objfiles.h, infcmd.c, printcmd.c, stack.c, typeprint.c,
valarith.c, valops.c, valprint.c, value.h, values.c: Replace
value with value_ptr. This is for the ptx compiler.
* objfiles.h, target.h: Don't declare a "sec_ptr" field using a
"sec_ptr" typedef.
* symm-nat.c: Add a bunch of stuff for symmetry's ptrace stuff.
#if 0 i386_float_info.
* symm-tdep.c (round): Remove. Also remove sgttyb.
* symm-tdep.c: Remove lots of stuff which duplicates stuff from
i386-tdep.c. Remove register_addr and ptx_coff_regno_to_gdb.
* i386-tdep.c (i386_frame_find_saved_regs): Put in
I386_REGNO_TO_SYMMETRY check in case it is needed for Dynix
someday.
* config/i386/nm-symmetry.h: Change KERNEL_U_ADDR. Move
stuff from PTRACE_READ_REGS, PTRACE_WRITE_REGS macros to
symm-nat.c. Define CHILD_WAIT and declare child_wait().
* config/i386/tm-symmetry.h: Remove call function stuff; stuff in
tm-i386v.h is apparently OK.
* config/i386/xm-symmetry.h [_SEQUENT_]: Define HAVE_TERMIOS not
HAVE_TERMIO. Define MEM_FNS_DECLARED, NEED_POSIX_SETPGID, and
USE_O_NOCTTY.
(bpstat_what_main_action): New code BPSTAT_WHAT_THROUGH_SIGTRAMP.
* breakpoint.c (bpstat_what): Return BPSTAT_WHAT_THROUGH_SIGTRAMP
if we hit a bp_through_sigtramp breakpoint. Remove kludge which
ignored bs->stop for a bp_step_resume breakpoint.
* infrun.c (wait_for_inferior): Make a through_sigtramp_breakpoint
which performs one (the check_sigtramp2 one) of the functions
which had been handled by the step_resume_breakpoint. For each
use of the step_resume_breakpoint, make it still use the
step_resume_breakpoint, use the through_sigtramp_breakpoint, or
operate on both.
Deal with BPSTAT_WHAT_THROUGH_SIGTRAMP return from bpstat_what.
When setting the frame address of the step resume breakpoint, set
it to the address for frame *before* the call instruction is
executed, not after.
various miscellaneous things discovered in the process:
* printcmd.c, defs.h (print_address_numeric): New function.
* c-valprint.c (c_val_print), ch-valprint.c (chill_val_print)
breakpoint.c (describe_other_breakpoints, breakpoint_1, mention),
cp-valprint.c (cplus_print_value), infcmd.c (jump_command),
printcmd.c, stack.c, symfile.c, symmisc.c, valprint.c:
Use it.
* utils.c, defs.h (gdb_print_address): New function.
* expprint (dump_expression), gdbtypes.h: Use it.
* breakpoint.c (describe_other_breakpoints),
symmisc.c (dump_symtab, print_symbol):
Use filtered not unfiltered I/O.
(remove_breakpoints): Remove BREAKPOINT_DEBUG code. Might as well
just run gdb under a debugger for this (and it had problems with
printing addresses, how to print b->shadow, etc.).
* buildsym.c (make_blockvector), core.c (memory_error),
exec.c (print_section_info), maint.c (print_section_table),
mdebugread.c (parse_procedure), solib.c, source.c, symfile.c,
symmisc.c, symtab.c, valops.c, valprint.c, xcoffexec.c:
Add comments saying code is broken. Marked with "FIXME-32x64".
* dbxread.c (process_one_symbol), partial-stab.h (default),
remote-vx.c (vx_run_files_info):
Don't cast int being passed to local_hex_string.
* symmisc.c (print_symbol): Don't cast long being passed to %lx.
* symtab.h (general_symbol_info): Add comment about SYMBOL_VALUE
only being a long.
* symmisc.c (print_symbol): Print "offset" in message for LOC_ARG
and LOC_LOCAL.
* printcmd.c (print_address): Remove #if 0 code with ADDR_BITS_REMOVE.
* source.c: Include <sys/types.h> regardless of USG.
step_resume_breakpoint for IN_SIGTRAMP cases.
* infrun.c (wait_for_inferior), breakpoint.h (struct bpstat_what),
breakpoint.c (bpstat_what): Move step_resume from its own field of
the struct bpstat_what into the main_action. Make it override
other breakpoints. This is a conservative change in the sense
that before the step resume breakpoint was a breakpoint.c
breakpoint, hitting the step resume breakpoint overrode even
calling bpstat_stop_status.
Change all references to stdout/stderr to gdb_stdout/gdb_stderr.
Replace all calls to stdio output functions with calls to
corresponding _unfiltered functions (`fprintf_unfiltered')
Replaced calls to fopen for output to gdb_fopen.
Added sufficient goo to utils.c and defs.h to make the above work.
The net effect is that stdio output functions are only directly used
in utils.c. Elsewhere, the _unfiltered and _filtered functions and
GDB_FILE type are used.
In the near future, GDB_FILE will stop being equivalant to FILE.
The semantics of some commands has changed in a very subtle way:
called in the right context, they may cause new occurences of
prompt_for_continue() behavior. The testsuite doesn't notice anything
like this, though.
Please respect this change by not reintroducing stdio output
dependencies in the main body of gdb code. All output from commands
should go to a GDB_FILE.
Target-specific code can still use stdio directly to communicate with
targets.
that clears the `inserted' flag for all breakpoints and deletes
any breakpoints which should go away between runs of programs.
* inflow.c (generic_mourn_inferior), infrun.c (init_wait_for_inferior),
remote-es.c (es1800_load), comments in exec.c and corelow.c:
Use it instead of mark_breakpoints_out.
* breakpoint.c (mark_breakpoints_out): Update comment, tm-rs6000.h
uses it in a completely different context.
* breakpoint.c (breakpoint_re_set_one): Add bp_call_dummy case.
* alpha-nat.c, alpha-tdep.c, config/alpha/alpha-osf1.mt,
config/alpha/nm-alpha.h, config/alpha/tm-alpha.h, osfsolib.c:
New files.
* Makefile.in: Add new files and dependencies.
* configure.in: Add alpha target.
* config/alpha/alpha-osf1.mh (NATDEPFILES): Add osfsolib.o
* config/alpha/alpha-osf1.mh (MH_CFLAGS): Remove, we can handle
shared libraries now.
* config/alpha/xm-alpha.h: Cleanup, get MAKEVA_* defines right.
* defs.h (CORE_ADDR): Make its type overridable via CORE_ADDR_TYPE,
provide `unsigned int' default.
* breakpoint.c (breakpoint_auto_delete): Delete only if we really
stopped for the breakpoint.
* stabsread.c, stabsread.h (define_symbol): Change valu parameter
to a CORE_ADDR.
* stabsread.c (read_range_type): Handle the case where the lower
bound overflows and the upper doesn't and the range is legal.
* infrun.c (resume): Do not step a breakpoint instruction if
CANNOT_STEP_BREAKPOINT is defined.
* inferior.h (CALL_DUMMY_LOCATION): New variant AT_ENTRY_POINT.
Now that we have the bp_call_dummy breakpoint the call dummy code
is no longer needed. PUSH_DUMMY_FRAME, PUSH_ARGUMENTS and
FIX_CALL_DUMMY can be used to set up everything for the dummy.
The breakpoint for the dummy is set at the entry point and thats it.
* blockframe.c (inside_entry_file, inside_entry_func): Do not stop
backtraces if pc is in the call dummy at the entry point.
* infcmd.c (run_stack_dummy): Handle AT_ENTRY_POINT case. Use
the expected breakpoint pc when setting up the frame for
set_momentary_breakpoint.
* symfile.c (entry_point_address): New function for AT_ENTRY_POINT
support.
* valops.c (call_function_by_hand): Handle AT_ENTRY_POINT case.
infcmd.c (step_1),
infrun.c (wait_for_inferior): collapse SHIFT_INST_REGS ifdef and insert macro.
* m88k-tdep.c: include ieee-float.h. new global target_is_m88110.
new const struct ext_format_m88110 for float format.
(pic_prologue_code): add braces.
(next_insn): remove unused variable buf.
(frame_find_saved_regs): remove unused variables next_addr,
saved_regs, regnum.
(frame_locals_address): remove unused variables frame, ap.
(frame_args_address): remove unused variables frame, ap.
(push_parameters): add some breaks and a default case.
* remote-bug.c: remove redundant includes of value.h, target.h,
serial.h.
(bug_open): corrected typo, sr_multi_scan -> gr_multi_scan.
(bug_fetch_register): special case sfip register for m88110.
remove flag bit masking of pc registers. This should be handled
by the ADDR_BITS_* macros.
(bug_store_register): special case sfip register for m88110.
Corrected sprint format for extended registers.
Some of the following is in #ifdef CALL_DUMMY_BREAKPOINT_OFFSET.
* breakpoint.h (enum bptype): Add bp_call_dummy.
(struct bpstat_what): Add call_dummy field.
* infrun.c (wait_for_inferior): Deal with it.
* breakpoint.c (bpstat_what): Deal with call dummy breakpoint.
* infcmd.c (run_stack_dummy): Set the call dummy breakpoint.
* config/sparc/tm-sparc.h: Define CALL_DUMMY_BREAKPOINT_OFFSET.
* stabsread.c (define_symbol): Make the caddr_t hack apply to `function
returning foo' as well as `pointer to foo'.
* remote.c [REMOTE_BREAKPOINT]: Use for breakpoint insn if defined.
* config/m68k/tm-m68k.h: Define it.
* mem-break.c, breakpoint.c: Improve comments.
Tue Jul 13 13:35:31 1993 Frederic Pierresteguy (F.Pierresteguy@frcl.bull.fr)
* config/m68k/tm-dpx2.h: Replace "tm-68k.h" with "m68k/tm-m68k.h".
* config/m68k/xm-dpx2.h: Define HAVE_TERMIOS not HAVE_TERMIO.
val.end is in the same function, not minimal symbols.
* source.c (line_info): Add a few more wrap_here's.
* i386-tdep.c (i386_follow_jump): Do byteswapping where needed and
don't make assumptions about sizes of host data types.
* blockframe.c, symtab.h (find_pc_partial_function): New arg endaddr.
* infrun.c, breakpoint.c, printcmd.c: Change callers.
* printcmd.c (containing_function_bounds): Remove.
* printcmd.c (disassemble_command): Use find_pc_partial_function,
not containing_function_bounds.
* infcmd.c (step_1): Use find_pc_partial_function rather than
trying to roll our own. Move check for a pc between SIGTRAMP_START and
SIGTRAMP_END in find_pc_partial_function, not step_1.
step_resume_break_address with step_resume_breakpoint (now local
to wait_for_inferior).
({insert,remove}_step_breakpoint): Remove.
(wait_for_inferior): Set step resume break with
set_momentary_breakpoint. Test hitting it with bpstat_stop_status
and bpstat_what (stop_step_resume_break removed).
* breakpoint.{h,c}, infrun.c: Return value from bpstat_what now struct
which includes previous return value as main_action, and a step_resume
bit.
* breakpoint.c (delete_breakpoint): If breakpoint was inserted, and
there is another breakpoint there, insert it.
* infrun.c (wait_for_inferior): Rearrange the spaghetti a bit. Use
a few more gotos.
Various: Clean up and add comments.
Remove bpstat_momentary_breakpoint. This was always kludgy
and is no longer used.
* breakpoint.h: Add enum bpstat_what.
breakpoint.h (struct bpstat), breakpoint.c (bpstat_stop_status):
stop and print fields of bpstat now per-breakpoint, not just
one for the whole chain.
breakpoint.{c,h} (bpstat_what): New function.
breakpoint.h: Remove bpstat_stop and bpstat_should_print.
infrun.c: Replace switch (stop_bpstat->breakpoint_at->type)
with call to bpstat_what.
README: Remove watchpoint/breakpoint bug from known bugs.
* breakpoint.h: Prototype bpstat_find_breakpoint.
* command.c (do_setshow_command): Use %u with var_{u,z}integer.
* command.{c,h}: New var_type var_integer.
main.c: Use it for history_size.
* rs6000-tdep.c, xcoffexec.c, config/rs6000/xm-rs6000.h, breakpoint.c:
Lint and byte-order fixups.
breakpoint.c (bpstat_print): Use it.
(print_it_normal): New function (from old bpstat_print code).
(bpstat_{alloc,stop_status}): Set print_it field.
* breakpoint.c (bpstat_stop_status): Use catch_errors when
evaluating watchpoint condition, via new function watchpoint_check.
Also stop if watchpoint disabled due to leaving its block.
