* config/tc-mips.c (mips_ip): Only perform range check when
dealing with O_constant expressions.
Problem noticed by QMS, where "%lo(SYM + LARGEOFFSET)" would complain
about the OFFSET being greater than 16bits or not absolute, when it
should really just be taking the lo-16bits of the final address value.
sis.h: Get rid of all uses of long long's.
* (close_port read_uart write_uart uarta_tx): Don't seg fault
when can't open pty's.
* exec.c: Add two new instructions: smul, and divscc.
* interf.c (flush_windows): New routine to flush the register
windows out to the stack just before returning to GDB. Makes
backtraces work much better.
config/sparc/tm-sparclite.h: Initialize tm_print_insn from
TM_PRINT_INSN, which comes from the tm file.
* Makefile.in (INTERNAL_LDFLAGS): Add in flags from configure.
* configure configure.in: Only make sol-thread.o for native.
Also, switch to dlopened libthread_db.so.1.
* sol-thread.c: Switch to using dlopen to get the thread_db
library.
* configure, configure.in: Change test for libthread_db to only
work for configs where build/host/target are the same.
registers.
* config/tc-m68k.c (mcf5200_control_regs): New variable,
array of control registers for the coldfire.
(cpu_of_arch): Added mcf5200.
(archs): Added mcf5200.
(init_table): Add new control registers.
(m68k_ip): Added support for new control registers.
(m68k_init_after_args): Likewise.
* config/tc-m68k.c (md_show_usage): Add -m5200 to usage text.
SEC_LOAD set.
* compile.c (sim_resume, case "O_NOT"): Use ONOT instead
of OSHIFTS.
(ONOT): Define.
(sim_resume, shift/rotate cases): Add support for shift/rotate
by two bits.
(OSHIFTS): Corresponding changes.
Handling more H8/S ops.
* h8300.h (UNOP3): Mark the register operand in this insn
as a source operand, not a destination operand.
(SHIFT_2, SHIFT_IMM): Remove. Eliminate all references.
(UNOP3): Change SHIFT_IMM to IMM for H8/S bitops. Mark
register operand with SRC_IN_DST.
More hackery for new shift ops on the H8/S.
* libbfd.h: Rebuild.
* i386lynx.c (KEEPIT): Define as udata.i.
(NAME(lynx,swap_std_reloc_out)): Don't use stoi.
(NAME(lynx,swap_ext_reloc_out)): Likewise.
* riscix.c (riscix_swap_std_reloc_out): Use udata.i rather than
flags. Don't use stoi.
with XCOFF_DEF_DYNAMIC set is really defined.
(xcoff_link_check_dynamic_ar_symbols): Likewise.
The above is for PR 9997.
(xcoff_link_add_symbols): Only create special sections if using an
XCOFF hash table.
* elf64-alpha.c (struct alpha_elf_link_hash_entry): Add flags
field.
(ALPHA_ELF_LINK_HASH_LU_ADDR): Define.
(ALPHA_ELF_LINK_HASH_LU_MEM): Define.
(ALPHA_ELF_LINK_HASH_LU_FUNC): Define.
(elf64_alpha_link_hash_newfunc): Initialize flags field.
(elf64_alpha_check_relocs): Record types of LITUSE entries that
are found for LITERAL relocs.
(elf64_alpha_adjust_dynamic_symbol): If a symbol has its address
taken, we cannot generate a .plt entry for the symbol.
