understand what it is trying to do, but I suspect it's not doing
it.
* config/ns32k/merlin.mh: Add comment about M_INSTALL.
* config/m88k/{delta88.mh,delta88v4.mh}: Remove M_INSTALL and
M_UNINSTALL; it tries to install a non-existent file gdb.z.
* Makefile.in: Remove M_INSTALL stuff; the above were the only uses.
about SHIFT_INST_REGS.
* exec.c (exec_file_command): Set text_end based on all code readonly
sections, not just ".text".
* defs.h, infcmd.c, config/z8k/tm-z8k.h, config/m88k/tm-m88k.h,
config/sh/tm-sh.h, config/h8300/tm-h8300.h, config/h8500/tm-h8500.h,
z8k-tdep.c: Remove all references to ADDR_BITS_SET.
* config/m88k/tm-m88k.h: Define TARGET_WRITE_PC.
* config/m88k/tm-m88k.h: Add definitions for calling functions.
(TARDIRS): Add gdbserver.
* exec.c (print_section_info): Print entry point.
* i386lynx-nat.c (i386lynx_saved_pc_after_call): Move into
i386lynx-tdep.c. Add core file support.
* i386lynx-tdep.c: New module for Lynx/386 target dependant code.
* maint.c: Add `maint info sections' command to print info about all
sections that BFD knows about for exec and core files.
* sparc-tdep.c (sparc_push_dummy_frame): Update stack pointer
before putting frame on the stack. Consolidate writes to reduce
traffic for remote debugging.
* config/i386/i386lynx.mh (NATDEPFILES): Remove exec.o.
* config/i386/i386lynx.mt (TDEPFILES): Add exec.o, i386lynx-tdep.o.
* config/i386/nm-i386lynx.h: Add target_pid_to_str().
* config/i386/tm-i386lynx.h: Remove target_pid_to_str().
* sparclite/Makefile.in: Add deps to keep Sun make happy.
ieee-float.h. expanded to cope with m88110 extended registers.
(R0_REGNUM, XFP_REGNUM, X0_REGNUM): new macros.
(SHIFT_INST_REGS): becomes a real macro.
Some of the following is in #ifdef CALL_DUMMY_BREAKPOINT_OFFSET.
* breakpoint.h (enum bptype): Add bp_call_dummy.
(struct bpstat_what): Add call_dummy field.
* infrun.c (wait_for_inferior): Deal with it.
* breakpoint.c (bpstat_what): Deal with call dummy breakpoint.
* infcmd.c (run_stack_dummy): Set the call dummy breakpoint.
* config/sparc/tm-sparc.h: Define CALL_DUMMY_BREAKPOINT_OFFSET.
* remote-sim.c: Add remote debug feature. Rename stuff to distinguish
interface to simulator from gdb-specific stuff. Other changes.
start-sanitize-v9
* remote-sp64sim.c: Renamed to remote-sim.c.
Use sr_get_debug instead of our own sim_verbose/simif_snoop.
Use gnutarget in call to bfd_openr.
Rename simif_* to gdbsim_*.
* config/sparc/sp64sim.mt: Change remote-sp64sim.c to remote-sim.c.
end-sanitize-v9
to tm-a29k.h and a29k-tdep.c and make it an enum.
* a29k-tdep.c (a29k_get_processor_type): New function. Fix many
aspects of how we detected the processor type.
* remote-udi.c, remote-adapt.c, remote-mm.c (*_open): Call it
rather than figuring out the type ourselves.
* exec.c (ignore): Return 0.
* stack.c (return_command): Fetch lazy value directly, not via
VALUE_CONTENTS, to avoid "value computed is not used".
* inflow.c (new_tty): Move osigttou inside #if.
* remote.c (remote_fetch_registers): If remote reply is short, just
note that fact and keep going (reading extra registers as all bits 0).
(remote_store_registers): Send number of registers that were found
by remote_fetch_registers.
* m68k-tdep.c, config/m68k/tm-m68k.h, config/m68k/tm-*.h: Remove
HAVE_68881. Define CANNOT_STORE_REGISTER if ptrace() can't write
floating registers.
* config/m68k/{tm-m68k-nofp.h,m68k-nofp.mt,tm-m68k-fp.h,m68k-fp.mt}:
Remove, replaced by {tm-m68k-em.h,m68k-em.mt}.
* Makefile.in, configure.in: Change accordingly.
Include sys/types.h regardless of USG.
* configure.in: Fix typo (delta88r4 -> delta88v4).
* config/m88k/xm-delta88.h: Don't include sys/siginfo.h. It was
to make this work on SVR4 before SVR4 had its own configuration,
and it breaks SVR3.
* config/m88k/m88k.mh: Use xm-dgux.h.
* config/m88k/xm-m88k.h: New file, with HOST_BYTE_ORDER,
MAKEVA_END and MAKEVA_ARG.
* config/m88k/xm-*.h: Include m88k/xm-m88k.h.
* printcmd.c: Remove __INT_VARARGS_H code; now in xm-m88k.h.
* config/m88k/xm-m88k.h: New file, with HOST_BYTE_ORDER,
MAKEVA_END and MAKEVA_ARG.
* config/m88k/xm-*.h: Include m88k/xm-m88k.h.
* printcmd.c: Remove __INT_VARARGS_H code; now in xm-m88k.h.
it conditionalized on 4.3 vs. 4.4.
* config/m68k/nm-hp300bsd.h: Move REGISTER_U_ADDR out of 4.3 and
4.4 sections; it was identical and now works for 4.4.
non-existent files nm-delta.h, etc.
* config/m68k/tm-delta68.h: Define CANNOT_STORE_REGISTER.
* delta68-nat.c: Add "[0]" in offsetof argument.
* delta68-nat.c (_initialize_kernel_u_addr): Don't try to set up
nl with initializer, just assign to it. Check n_scnum field on
return.
(FP_REGNUM): define in terms of SP_REGNUM
rather than by absolute number. Also clearly comment that this
is a convenient lie in order to decrease future confusion.
(ACTUAL_FP_REGNUM): new macro for FP.
(FRAME_CHAIN_VALID): removed. Standard default works fine.
* m88k-tdep.c (frame_chain_valid): redundant, so removed.
(NEXT_PROLOGUE_INSN): removed unused fourth arg, fixed all
callers.
(read_next_frame_reg): declare static.
(examine_prologue): removed unused variabel insn2, rename insn1
to insn, rewrote comment about finding fp, sp, etc. set frame_fp
based on ACTUAL_FP_REGNUM rather than FP_REGNUM which is
actually a scammed alias for SP_REGNUM on m88k.
