* Makefile.in (SIM_EXTRA_CFLAGS): Add -lm.
* armdefs.h (ARMdval, ARMfval): New types.
(ARM_VFP_reg): New union.
(struct ARMul_State): Add VFP_Reg and FPSCR fields.
(VFP_fval, VFP_uword, VFP_sword, VFP_dval, VFP_dword): Accessor
macros for the new VFP_Reg field.
* armemu.c (handle_v6_insn): Add code to handle MOVW, MOVT,
QADD16, QASX, QSAX, QSUB16, QADD8, QSUB8, UADD16, USUB16, UADD8,
USUB8, SEL, REV, REV16, RBIT, BFC, BFI, SBFX and UBFX
instructions.
(handle_VFP_move): New function.
(ARMul_Emulate16): Add checks for newly supported v6
instructions. Add support for VMRS, VMOV and MRC instructions.
(Multiply64): Allow nRdHi == nRm and/or nRdLo == nRm when
operating in v6 mode.
* armemu.h (t_resolved): Define.
* armsupp.c: Include math.h.
(handle_VFP_xfer): New function. Handles VMOV, VSTM, VSTR, VPUSH,
VSTM, VLDM and VPOP instructions.
(ARMul_LDC): Test for co-processor 10 or 11 and pass call to the
new handle_VFP_xfer function.
(ARMul_STC): Likewise.
(handle_VFP_op): New function. Handles VMLA, VMLS, VNMLA, VNMLS,
VNMUL, VMUL, VADD, VSUB, VDIV, VMOV, VABS, VNEG, VSQRT, VCMP,
VCMPE and VCVT instructions.
(ARMul_CDP): Test for co-processor 10 or 11 and pass call to the
new handle_VFP_op function.
* thumbemu.c (tBIT, tBITS, ntBIT, ntBITS): New macros.
(test_cond): New function. Tests a condition and returns non-zero
if the condition has been met.
(handle_IT_block): New function.
(in_IT_block): New function.
(IT_block_allow): New function.
(ThumbExpandImm): New function.
(handle_T2_insn): New function. Handles T2 thumb instructions.
(handle_v6_thumb_insn): Add next_instr and pc parameters.
(ARMul_ThumbDecode): Add support for IT blocks. Add support for
v6 instructions.
* wrapper.c (sim_create_inferior): Detect a thumb address and call
SETT appropriately.
* armdefs.h: Define ARMsword and ARMsdword. Use stdint.h when
available.
* armemu.c: Use them.
* armvirt.c (ARMul_MemoryInit): Use correct type for size.
* configure.ac: Check for stdint.h.
* config.in: Regenerate.
* configure: Regenerate.
(ARMulEmulate32): Call handle_v6_insn when a possible v6 insn is found.
* armdefs.h (struct ARMul_State): Add new field: is_v6.#
(ARM_v6_Prop): Define.
* arminit.c (ARMul_NewState): Initialise the v6 flag.
(ARMul_SelectProcessor): Determine if the v6 flag should be set.
* wrapper.c (sim_create_inferior): For unknown architectures, default to allowing the v6 instructions.
2001-04-18 matthew green <mrg@redhat.com>
* armcopro.c (write_cp15_reg): Set CHANGEMODE if endianness changes.
(read_cp15_reg): Make non-static.
(XScale_cp15_LDC): Update for write_cp15_reg() change.
(XScale_cp15_MCR): Likewise.
(XScale_cp15_write_reg): Likewise.
(XScale_check_memacc): New function. Check for breakpoints being
activated by memory accesses. Does not support the Branch Target
Buffer.
(XScale_set_fsr_far): New function. Set FSR and FAR for XScale.
(XScale_debug_moe): New function. Set the debug Method Of Entry,
if configured.
(write_cp14_reg): Reset count counter if requested.
* armdefs.h (struct ARMul_State): New members `LastTime' and
`CP14R0_CCD' used for the timer/counters.
(ARMul_CP13_R0_FIQ, ARMul_CP13_R0_IRQ, ARMul_CP13_R8_PMUS,
ARMul_CP14_R0_ENABLE, ARMul_CP14_R0_CLKRST, ARMul_CP14_R0_CCD,
ARMul_CP14_R0_INTEN0, ARMul_CP14_R0_INTEN1, ARMul_CP14_R0_INTEN2,
ARMul_CP14_R0_FLAG0, ARMul_CP14_R0_FLAG1, ARMul_CP14_R0_FLAG2,
ARMul_CP14_R10_MOE_IB, ARMul_CP14_R10_MOE_DB, ARMul_CP14_R10_MOE_BT,
ARMul_CP15_R1_ENDIAN, ARMul_CP15_R1_ALIGN, ARMul_CP15_R5_X,
ARMul_CP15_R5_ST_ALIGN, ARMul_CP15_R5_IMPRE, ARMul_CP15_R5_MMU_EXCPT,
ARMul_CP15_DBCON_M, ARMul_CP15_DBCON_E1, ARMul_CP15_DBCON_E0): New
defines for XScale registers.
(XScale_check_memacc, XScale_set_fsr_far, XScale_debug_moe): Prototype.
(ARMul_Emulate32, ARMul_Emulate26): Clean up function definition.
(ARMul_Emulate32): Handle the clock counter and hardware instruction
breakpoints. Call XScale_set_fsr_far() for software breakpoints and
software interrupts.
(LoadMult): Call XScale_set_fsr_far() for data aborts.
(LoadSMult): Likewise.
(StoreMult): Likewise.
(StoreSMult): Likewise.
* armemu.h (write_cp15_reg): Update prototype.
* arminit.c (ARMul_NewState): Initialise CP14R0_CCD and LastTime.
(ARMul_Abort): If XScale, check for FIQ and IRQ being enabled in CP13
register 0.
* armvirt.c (GetWord): Call XScale_check_memacc().
(PutWord): Likewise.
(ARM_Strong_Prop, STRONGARM): Define.
* arminit.c (ARMul_NewState): Reset is_StrongARM.
(ARMul_SelectProcessor): Set is_StrongARM.
* wrapper.c (sim_create_inferior): Use bfd machine type to
determine processor type to emulate.
* armemu.h (BUSUSEDINCPCS, BUSUSEDINCPCN): Don't increment PC
when emulating StrongARM.