All references to value changed to value_ptrlage_command is now
called big_command.
All references to value changed to value_ptr.
* remote-z8k.c (e7000_wait): Use target_waitstatus and SETSTOP
* remote-hms.c (hms_wait): Timeout after five seconds.
* ser-go32.c (dosasync_read): Poll if timeout < 0.
* config/tm/tm-h8500.h (BEFORE_MAIN_LOOP_HOOK): Deleted.
* config/sh/tm-sh.h (BREAKPOINT): Is now sleep opcode.
* h8500-tdep.c (saved_pc_after_call): The size of the
pc is memory model dependent. (segmented_command,
unsegmented_command, _initialize_h8500_tdep): New commands to
change memory model.
* remote-7000.c (initialize_remote_e7000): Change name of snoop
command.
* remote-hms.c (hms_load): Remove breakpoints when loaded.
(hms_wait): Use new status structure
(hms_open): Push the target here. (hms_before_main_loop): Not
here. (supply_val, hms_fetch_register, hms_store_register): Cope
with H8/500 names too.
* sh-tdep.c (show_regs, initialize_sh_tdep): New command to print
all registers in a compact way.
(go32_readchar): Special handling for faster polling. (async
structure): Volatile.
* h8300-tdep.c (print_register_hook): Allocate and use the right
number bytes for the raw register.
* h8500-tdep.c (regoff, frame_find_saved_reg, examine_prologue):
deleted. (h8500_register_size, h8500_register_virtual_type, ):
Use new way of counting registers.
* remote-e7000.c (echo_index): deleted. (expect): Better handling
of user interrupts. (expect_prompt): Remove never used log file
support. (want, want_nopc): Add support for H8/300H.
(fetch_regs_from_dump): Treat \r and \n as whitespace.
(e7000_drain): Send an "end" command before waiting for output to
stop. (e7000_wait): Cope with H8/300H, better handling of user
interrupts. (why_stop, expect_n, sub2_from_pc): New function.
* remote-utils.c (gr_load_image): call fflush and QUIT more regularly.
* utils.c (notice_quit): New function for polling for user interrupts.
Change all references to stdout/stderr to gdb_stdout/gdb_stderr.
Replace all calls to stdio output functions with calls to
corresponding _unfiltered functions (`fprintf_unfiltered')
Replaced calls to fopen for output to gdb_fopen.
Added sufficient goo to utils.c and defs.h to make the above work.
The net effect is that stdio output functions are only directly used
in utils.c. Elsewhere, the _unfiltered and _filtered functions and
GDB_FILE type are used.
In the near future, GDB_FILE will stop being equivalant to FILE.
The semantics of some commands has changed in a very subtle way:
called in the right context, they may cause new occurences of
prompt_for_continue() behavior. The testsuite doesn't notice anything
like this, though.
Please respect this change by not reintroducing stdio output
dependencies in the main body of gdb code. All output from commands
should go to a GDB_FILE.
Target-specific code can still use stdio directly to communicate with
targets.
cleans up all kinds of hassles (which nm to use in munch, etc). The
new formatting conventions (mostly already followed) are that
the name of the _initialize_* routines must start in column zero,
and must not be inside #if.
* munch: Removed.
* Makefile.in: Remove references to munch.
* serial.c, remote.c, infptrace.c, maint.c, convex-tdep.c,
alpha-tdep.c, hp300ux-nat.c, hppab-nat.c, osfsolib.c, remote-es.c,
procfs.c, remote-udi.c, ser-go32.c, ultra3-xdep.c, sh-tdep.c,
i960-tdep.c, hppa-tdep.c, h8500-tdep.c, dpx2-nat.c, delta68-nat.c,
z8k-tdep.c: Make sure the above conventions are followed. Make
sure they are all declared as returning void. Clean up
miscellaneous comments and such.
if we are looking at short pointer. If so, skip crock.
* h8500-tdep.c (h8500_frame_chain): Mask down value from
read_memory_integer() to avoid getting messed up by sign extension.
of reading/writing registers that are shorter than REGISTER_TYPE.
* (value_from_register): Install H8500 specific code to return
proper value when register is being used as a pointer.
* h8500-tdep.c: Remove extra defines of NUM_REGS.
(h8500_skip_prologue): Use correct lengths for LINK instructions.
(FRAME_CHAIN): Change name to h8500_frame_chain. Rewrite code to
chain frames properly by combining frame pointer with T reg.
(init_extra_frame_info): Delete. It's now a macro.
(frame_args_address): Don't add PTR_SIZE. Stack args are already
offset by the correct amount off of the frame pointer.
(register_byte): Delete. It's now a macro.
(register_raw_size, register_virtual_size): Delete. Replaced by
common routine h8500_register_size, cuz there's no difference
between the raw & virtual sizes on this machine.
(register_convert_to_raw, register_convert_to_virtual): Delete,
cuz there's no difference between the raw & virtual forms.
Replaced by memcpy in tm file.
(register_virtual_type): Rename to h8500_register_virtual_type.
Get rid of pointer pseudo-regs, use _REGNUM with all reg names.
(_initialize_h8500_tdep): Get rid of crock to ensure that GDB &
emulator have same reg offsets. This is all handled in the
simulator code now.
(h8500_trapped_internalvar): New routine to detect references to
convenience vars acting as pointer pseudo-regs.
(h8500_value_trapped_internalvar): Conjure up value of pointer
pseudo-regs.
(h8500_set_trapped_internalvar): Convert set value in real
register references.
infcmd.c (read_pc, write_pc): Add h8500 specific code to handle
code segment register.
infrun.c (proceed): Simplify. Call write_pc instead of doing it
by hand.
(wait_for_inferior): Add h8500 specific code to add stack segment
when reading SP register.
remote-sim.c (fetch_register): Spacing.
tm-h8500.h: #define GDB_TARGET_IS_H8500 to make it easier to
detect cruft. Redo all register manipulation stuff. Get rid of
pointer pseudo-regs. (INIT_EXTRA_FRAME_INFO): Adds stack segment
to frame pointer. (IS_TRAPPED_INTERNALVAL,
VALUE_OF_TRAPPED_INTERNALVAR, SET_TRAPPED_INTERNALVAR): Use these
to create internal vars for pointer pseudo-regs.
